Range Repair Tips
Whether you are in need of electric Range repair or gas Range repair . If your Range is having problems like the Range surface Element won’t work, Range burner has spark problems, Range surface element won’t turn off, Range burners spark all the time. Range Repair will put you right back where you need to be. Our Range repair technicians carry most Range parts. Appliance Repair Los Angeles will have your Range repaired or Serviced in no time. We will have your Range up in running in no time.
Range Repair Tips
Make sure there’s power getting to your range, oven or cook top. Check for a tripped circuit breaker or a blown fuse. Check the wall socket for power with a voltmeter or by plugging something else in.
Range Top burner doesn’t work
A lot of times the problem is with a dirty or a clogged burner. Make sure the burner is clean.
If you have a pilotless model, it uses a spark igniter to ignite the gas, which works in a combination with a spark switch (located on the burner gas valve) and a spark module. Because it is not simple to test these parts and find out which one is defective, we recommend to contact a professional appliance technician.
Range doesn’t bake
Bake igniter
When the bake igniter becomes weak or burns out, your oven would not bake. The bake igniter is usually mounted on the oven burner. It’s about 1 inch by 4-8 inches (depending on the model), and comes in round or flat styles. If you don’t see the igniter glow at all, it’s probably burned out. Replace the igniter if found defective. Note: one of the exceptions could be that your oven is set to automatic mode instead of manual. If this is the case, set your oven to manual mode and check again.If the bake igniter glows red and not bright yellow or white, it is probably because it is too weak. When this happens, the safety valve would not let the gas out into the oven burner. A weak igniter must be replaced.
A faulty igniter is probably the most common cause, however there are others:
— defective thermostat
— defective selector switch
— defective gas safety valve
If you are certain the igniter is ok, it might be a good idea to call a professional appliance technician.
Range doesn’t broil
Broil igniter
When the broil igniter becomes weak or burns out, your oven would not broil. The broil igniter is usually mounted on the oven burner. It’s about 1 inch by 4-8 inches (depending on the model), and comes in round or flat styles. If you don’t see the igniter glow at all, it’s probably burned out. Replace the igniter if found defective. Note: one of the exceptions could be that your oven is set to automatic mode instead of manual. If this is the case, set your oven to manual mode and check again.If the broil igniter glows red and not bright yellow or white, it is probably because it is too weak. When this happens, the safety valve would not let the gas out into the oven burner. A weak igniter must be replaced.
A faulty igniter is probably the most common cause, however there are others:
— defective thermostat
— defective selector switch
— defective gas safety valve
If you are certain the igniter is ok, it might be a good idea to call a professional appliance technician.
Range doesn’t work at all
1. No power
Make sure there’s power getting to your range, oven or cooktop. Check for a tripped circuit breaker or a blown fuse. Check the wall socket for power with a voltmeter. Sometimes the power cord disconnects or burns at the appliance, if this is the case, the wiring and the terminal block must be repaired or replaced.
Range Top element doesn’t work
1. Top element
If the element only works partially or not getting red hot at the “Hi” setting, the problem might be with a burned out receptacle that the element plugs into. If this is the case, replace both the element and the receptacle.You can usually tell when the element itself burns out. It might have small holes or bubbles on the coil. Replace the element, if found defective.
2. Infinite switch
Another reason, why the element would not start, might be a defective infinite switch (located behind the control panel, with the burner knob on its shaft). Replace the switch if found defective.
Range doesn’t bake
1. Bake element
Replace if found defective
Range doesn’t broil
1. Broil element
Replace if found defective