Dishwasher Repair Tips

Dishwasher Repair Tips offers tips in all types of Dishwasher repair. If your Dishwasher is in need of repair or Service or your having an issue with Dishwasher doesn’t clean, Dishwasher won’t drain, Dishwasher buttons don’t work, Dishwasher lights flashing or blinking, Dishwasher leaking, Dishwasher won’t start, Dishwasher won’t latch, Dishwasher dispenser doesn’t work, Dishwasher won’t fill, Dishwasher overflowing, Dishwasher won’t dry dishes. Dishwasher Repair will put you right back where you need to be. Appliance Repair will have your Dishwasher repaired   in no time. We will have your Dishwasher up in running in no time.

1. No power to the dishwasher
Make sure there’s power getting to the dishwasher. Check for a tripped circuit breaker or a blown fuse. Check the wall socket for power. Sometimes the power cord disconnects at the dishwasher (inside the junction box, behind the bottom kick panel), if this is the case, the wiring must be repaired or replaced.

2. Door switch
Replace if defective.

3. Timer
Replace if defective (note: uncommon problem).

4. Selector switch
Replace if defective (note: uncommon problem).

It doesn’t get the dishes clean

1. No water
Make sure you get water to the dishwasher. Check to see if the water shut-off valve (located under the sink) is open. If you get water to the dishwasher, but there is still no water inside during the fill cycle, the problem might be with a faulty water valve (located at the bottom of the dishwasher, behind the kick panel, on either side), in which case replace the water valve.

2. Not enough water
If there is not enough water, the dishes would not get cleaned. This could be caused by a partially closed water shut-off valve (located under the sink), or a faulty dishwasher water valve (located at the bottom of the dishwasher, behind the kick panel, on either side).

3. Clogged spay arms
There is usually two, sometimes three spray arms in a dishwasher. Make sure there is no debris blocking the holes inside each spray arm.

4. Water temperature is too low
To get the best results, the water has to be at 120 degrees Fahrenheit when entering the dishwasher.

5. Not enough soap
If you only fill one part of the soap cup, try adding soap to both parts.

6. Smoky film on dishes and glasses
This problem occurs due to excessive calcium build up inside the dishwasher. Try cleaning you dishwasher using a dishwasher cleaner. There are a few out there, we recommend

It doesn’t drain

1. Air gap / Drain hoses
If there is an air gap (located in the sink, near the faucet), check to see if it is clogged. Unscrew the top cap and see if there is anything blocking inside. Note: If there is no air gap installed, the dishwasher might not drain properly.

If the drain hose is clogged, the dishwasher would not drain. If there is an air gap installed, it is very common that a hose going from the air gap into the garbage disposer is clogged. Remove and clean the hose. Make sure to reattach the hose before starting the dishwasher.

Note: If you recently had a garbage disposer installed, it is common to overlook removing the drain plug.

2. Broken belt
Some dishwasher models use a belt to drive the pump. Replace the belt if found broken.

Note: Sometimes the belt would just come off the pump. Even though it might not be broken, it is recommended that you replace the belt, because it is probably too stretched out.

3. Pump
Some models have two impellers inside the pump – one, wash impeller, takes care of the wash cycles, the other, drain impeller, drains the water out. If the drain impeller is broken (broken blades, shaft), the dishwasher would not drain. Replace any broken pump components.

4. Drain solenoid
Some models (for example most GE dishwashers) use a drain solenoid to drain water out. Sometimes the solenoid gets stuck, preventing the water from draining out. Try to free up the solenoid. If unsuccessful, you might have to replace the pump assembly.

5. Motor
If the motor is stuck, it is sometimes possible to free it up by manually spinning the motor.

Replace the motor if defective.

6. Timer
Replace if defective (note: uncommon problem).

There is no water

Make sure you get water to the dishwasher. Check to see if the water shut-off valve (located under the sink) is open. If you get water to the dishwasher, but there is still no water inside during the fill cycle, the problem might be with a faulty water valve (located at the bottom of the dishwasher, behind the kick panel, on either side), in which case replace the water valve.