Whirlpool Washer Error Code: F8 E1 or LO FL
If the washer has an F8 E1 error or LO FL error, the door may be locked, and the control may be unresponsive. Press the power button, and the washer will start a drain routine, which takes approximately 8 to 10 minutes, during which the pump will run continuously. The control will not accept any input during this time. Please wait 10 minutes before trying to perform any functions.
Is the water turned on?
Ensure the Hot and Cold water valves are fully open; both hot and cold inlet hoses must be connected for the washer to operate correctly.
Check the water inlet hoses.
- Ensure the hoses are not kinked, which can restrict water flow.
- Are they connected correctly? Ensure the hot (red) hose is connected to the hot (red) water valve and the cold (blue) hose is connected to the cold (blue) water valve.
- Was an anti-flood device installed? The washer should be directly connected to the water supply for optimum machine performance. Using anti-flood devices can reduce the water pressure and amount of water entering the appliance.
Are the water inlet screens clogged?
The inlet screens on the washer can become clogged from mineral build-up or from capturing other debris in the water. To check the inlets:
- Turn the water supply off, then use pliers to remove the hoses.
- Place hose ends in a bucket to catch any remaining water.
- Check the inlet screens on the back of the water inlet valve.
- If they appear to be clogged, without removing the screen, clean them with a brush (an old toothbrush works great), mild soap, and water.
Is a water hose clogged?
The water supply hoses can get clogged by mineral build-up or other debris in the water. With the hoses uninstalled, at a sink or other water source, run water through the hoses. If water does not flow completely through the hose or the water stream seems to be restricted, it is recommended the hose be replaced.
Is the drain hose correctly installed?
If the drain hose is not properly installed, the washer will not drain properly. Check the following for proper installation:
- Drain hose extending more than 4.5″ (113 mm) into the drainpipe. Use the U-shape drain hose form to provide the correct drain hose length in the drainpipe or laundry tub.
- Drain hose is taped onto the drainpipe or top of the drain pipe covered in tape. Do not seal the drain hose into the drainpipe with tape. The drain hose should be loose, yet secure. There must be a gap between the drain hose and the drain pipe to allow airflow.
- Drainpipe (standpipe) less than the minimum height of 39″. Check that the top of the drain is at least 39″ (99 cm) high (as measured from the floor.) If the drain is below 39″ (99 cm), the water will start to flow out of the machine due to gravity.
Whirlpool Washer Error Code: F7 E1
Have the shipping bolts been removed?
All four (4) shipping bolts and the plastic spacers must be removed from the rear of the washer before you operate it. Each unit is shipped from the factory with four bolts, which are designed to secure the washer during shipping. Failure to remove all of the shipping bolts, and the four plastic spacers that are with them, can result in noise, vibration or error codes. See the Installation Instructions for details.
Is the washer overloaded?
The washer may be overloaded for the cycle you are running.
Remove a few items from the load.
See the Cycle Guide in the Owner’s Manual for loading suggestions for each cycle.
To remove displayed code:
- Press the Pause or Cancel button twice
- Press the Power button once
NOTE: The method for removing the displayed code varies by model
If code is still displayed:
- Unplug the washer or disconnect the power for one minute.
- Plug in the washer or reconnect the power.
- Re-select the cycle and press Start.
Whirlpool Washer Error Code: F5 E4
Was the washer run 3 times in a row?
If the washer shows an F5 E4 Error Code, this may be an indication that the machine may have been run for 3 consecutive cycles without opening the door in between cycles. This may occasionally happen if you have forgotten to remove your items from the washer, then realize they need to be rewashed.
In this case, the washer will generate an invalid beep tone when you press the “Start” button. To solve this issue, open and close the door.
Is the door switch obstructed?
Check the door switch to make sure there is nothing obstructing the operation. Lint, laundry additives, and clothing items could catch in that area, causing the obstruction.
Clear any item that may cause the door switch to be obstructed.
Whirlpool Washer Error Code: F5 E3
Is the door firmly closed?
The door must be completely closed for the washer to operate. The door may look as if it’s closed, but it may not be latched. Open the door and firmly close it.
Is there an item preventing the door from closing?
Before you close the washer door, check for laundry items sticking out beyond the door opening. Leave enough space in the washer to allow the clothes to freely tumble. Reduce your load size if needed.
To remove displayed code:
- Press the Pause or Cancel button twice
- Press the Power button once
Whirlpool Washer Error Code: F5 E2
Is the door firmly closed?
The door must be completely closed for the washer to operate. The door may look as if it’s closed, but it may not be latched. Open the door and firmly close it.
Is there an item preventing the door from closing?
Before you close the washer door, check for laundry items sticking out beyond the door opening. Leave enough space in the washer to allow the clothes to freely tumble. Reduce your load size if needed.
To remove displayed code:
- Press the Pause or Cancel button twice
- Press the Power button once
Whirlpool Washer Error Code: F22
Try to the following method to resolve:
Select PAUSE/CANCEL twice to cancel the cycle.
Check the following:
- Is the washer door firmly shut? The door must be completely closed for the washer to operate. The door may look closed, but may not be latched. Open the door and close firmly.
- Verify there is no wash media (detergent, fabric softener, etc) built up around the door lock. Clean with a soft damp cloth if needed.
- Were you washing a large load? Before you close the washer door, check for laundry items sticking out beyond the door opening. Leave enough space in the washer to allow the clothes to tumble freely. An overloaded basket may keep the door from shutting completely. Reduce your load size if needed.
- Press POWER and select START.
Whirlpool Washer Error Code: F21
Try the following method to resolve:
Select PAUSE/CANCEL twice to cancel the cycle. Unplug washer or disconnect power.
Check the following:
- Is the drain hose kinked?
- Is the drain hose frozen?
- Is the drain hose clogged?
- Is the drain hose more than 96″ (2.4 m) above the floor?
- Plug in washer or reconnect power. Re-select cycle and press START.
Whirlpool Washer Error Code: F20
Try the following method to resolve:
Select PAUSE/CANCEL twice to cancel the cycle. Unplug washer or disconnect power.
Check the following:
- Are both, hot and cold, water faucets completely turned on?
- Are screens at inlet hose connection to washer clogged?
- Are water inlet hoses kinked?
- Are water inlet hoses frozen?
- Plug in washer or reconnect power. Re-select cycle and press START.
Whirlpool Washer Error Code: Beeps
Error “Beeps” are an audible signal that the machine makes to alert the user that something is not right.
Typically this will happen if the washer door has not been opened and closed for at least 3 cycles. This code may appear when the washer is first turned on.
Open and close the door to clear the display.
Washer Beeps when START/PAUSE is Pressed.
If the washer just beeps when you press a cycle or an option, there could be a number of reasons:
- Door not closed. Close the door completely.
- You are trying to select an option that does not function with the cycle you have selected.
- An example would be trying to select Hot water for a Delicate cycle.
Whirlpool Washer Error Code: dET
