Kitchenaid Dishwasher Error Code 6-1 or F6E1

Kitchenaid Dishwasher Error Code 6-1 or F6E1

Check for an item stuck under the overfill float and remove it. If the overfill float sticks in the “up” position the dishwasher won’t fill. Unplug the dishwasher to disconnect electrical power and shut the water supply valve. Disconnect the water supply line from the water inlet valve and check the water inlet valve screen for clogs. Replace the water valve if you find the screen clogged because debris from the clog can get into the valve body, causing the valve to stick open and possibly flood your kitchen. If the screen is clear, place the end of the water supply line in a shallow pan and briefly open the water supply valve to see if water flows from the supply line. If water doesn’t flow, have a plumber repair the water supply to your dishwasher. If the water flows okay, check the wiring connections on the water inlet valve and reconnect any loose wires or replace the wire harness if damaged. If the wires are okay, you may need to replace the water inlet valve or the electronic control board.

Kitchenaid Dishwasher Error Code 5-2 or F5E2

Kitchenaid Dishwasher Error Code 5-2 or F5E2

Error code 5-2 or F5E2 on your KitchenAid dishwasher signals a situation where the control board detects that the dishwasher door hasn’t opened between cycles as expected. This error is crucial for the proper functioning of the dishwasher, as the control board relies on the door status to initiate subsequent cycles.

Possible Causes:

Door Switch Defect: The door switch, a vital component that signals the door’s open/closed status, may be malfunctioning.

Troubleshooting Steps:

1. Cancel the Current Cycle:
   • If you didn’t open the door between cycles, cancel the ongoing cycle using the dishwasher’s control panel.
2. Open and Shut the Door:
   • Manually open and securely close the dishwasher door.
   • Attempt to start a new cycle.
3. Simulate Door Opening:
   • Unplug the dishwasher from the power source.
   • Wait for a few minutes to ensure the control board resets.
   • Plug the dishwasher back in to simulate the door opening.
4. Attempt to Start a New Cycle:
   • Try initiating a new cycle after the simulated door opening.
   • If the cycle starts without issues, the problem may be related to the door switch.
5. Replace Door Latch Assembly:
   • If the issue persists, it’s likely that the door switch within the door latch assembly is defective.
   • Consider replacing the door latch assembly to ensure proper detection of the door opening.

Kitchenaid Dishwasher Error Code 5-1 or F5E1

Kitchenaid Dishwasher Error Code 5-1 or F5E1

Error code 5-1 or F5E1 on your KitchenAid dishwasher indicates a door switch failure. This error occurs when the dishwasher door is not closed within 4 seconds of pressing the Start/Resume button, or if the door latch assembly is broken.

Troubleshooting Steps:

1. Prompt Door Closure:
   • Start a cycle and ensure that you close the dishwasher door within 4 seconds of pressing the Start/Resume button.
2. Inspect Door Latch Assembly:
   • If the error persists, unplug the dishwasher to disconnect electrical power.
   • Disassemble the dishwasher door to access the door latch assembly.
3. Check Door Switch Wire Harness:
   • Inspect the door switch wire harness for any loose or disconnected wires.
   • Reconnect any loose wires securely.
4. Replace Damaged Wire Harness:
   • If the wire harness is damaged, replace it with a new one.
   • Ensure the replacement harness is compatible with your KitchenAid dishwasher model.
5. Examine Door Latch Assembly:
   • If the issue persists, replace the door latch assembly.
   • Consult your dishwasher’s manual for specific instructions on removing and installing the door latch assembly.

Remember, safety is paramount during any troubleshooting or repair process. Always disconnect the dishwasher from the power source before attempting any disassembly or maintenance. If uncertainties arise, it’s best to consult with professionals to address the KitchenAid Dishwasher Error Code 5-1 effectively.

Kitchenaid Dishwasher Error Code 4-4 or F4E4

Kitchenaid Dishwasher Error Code 4-4 or F4E4

Error code 4-4 (F4E4) on your KitchenAid dishwasher indicates a communication breakdown between the electronic control board and the circulation pump motor. This communication error disrupts the normal functioning of these critical components, potentially leading to operational issues.

1. Faulty Wiring Connections: Loose or damaged wires in the circulation pump wire harness can impede communication.
2. Circulation Pump and Motor Issues: A malfunction in the circulation pump and motor assembly may disrupt communication.
3. Electronic Control Board Malfunction: The electronic control board, responsible for coordinating dishwasher functions, may be faulty.

Troubleshooting Steps:

1. Disconnect Power:
   • Unplug the dishwasher to ensure your safety during troubleshooting.
2. Inspect Circulation Pump Wire Harness:
   • Examine the circulation pump wire harness for any loose or damaged wires.
   • Reconnect any loose wires or replace the entire wire harness if damage is detected.
3. Check Circulation Pump and Motor Assembly:
   • If the wiring connections are intact, inspect the circulation pump and motor assembly for signs of malfunction.
   • Replace the circulation pump and motor assembly if issues are identified.
4. Evaluate Electronic Control Board:
   • If the problem persists after addressing the pump and motor, turn your attention to the electronic control board.
   • Consider replacing the electronic control board if it is determined to be faulty.
5. Reconnect Power and Test:
   • After making repairs or replacements, plug the dishwasher back in.
   • Test the dishwasher to ensure the error code 4-4 (F4E4) is resolved.

Understanding and addressing the specifics of error code 4-4 (F4E4) ensures a smoother resolution to communication errors between the electronic control board and the circulation pump motor in your KitchenAid dishwasher.

Kitchenaid Dishwasher Error Code 3-3 or F3E3

Kitchenaid Dishwasher Error Code 3-3 or F3E3

Disconnect the dishwasher drain hose connection from the air gap or the garbage disposal if you have no air gap. Pour water through the drain hose to see if water backs up into the dishwasher tub. If so, replace the portion of the drain hose that connects to the drain pump because the check valve in that hose failed. If water doesn’t back up into the dishwasher through the drain hose, reconnect the hose and run the Service Diagnostics Test according to the instructions in the tech sheet. You should see low soil level indicated during the OWI test in the diagnostic mode. If you see high soil level during the OWI test, unplug the dishwasher and clean the OWI sensor. Reassemble the dishwasher and plug the dishwasher back in to restore electrical power. Run the diagnostic test cycle so the electronic control board will calibrate the OWI sensor on the next cycle. Run a normal wash cycle. If you still see the error code, replace the thermistor/OWI sensor.

Kitchenaid Dishwasher Error Code 3-2 or F3E2

Kitchenaid Dishwasher Error Code 3-2 or F3E2

rror code 3-2 or F3E2 on your KitchenAid dishwasher indicates a shorted thermistor or Optical Water Indicator (OWI) sensor. The thermistor/OWI sensor plays a crucial role in monitoring and regulating the water temperature during the dishwasher’s operation. A short circuit or malfunction in this component triggers the error.

1. Shorted Thermistor/OWI Sensor: Electrical issues or damage may cause a short circuit in the thermistor or OWI sensor.
2. Faulty Wiring: The wiring between the electronic control board and the thermistor/OWI sensor may be broken or damaged.

Troubleshooting Steps:

1. Unplug the Dishwasher:
   • Ensure the dishwasher is unplugged or disconnected from the power source to ensure safety during the troubleshooting process.
2. Inspect Wiring:
   • Carefully examine the wiring connecting the electronic control board to the thermistor/OWI sensor.
   • Look for any visible signs of damage, such as frayed wires or loose connections.
3. Repair or Replace Wire Harness:
   • If the wiring is damaged, repair or replace the wire harness. Use electrical tape for minor repairs, or replace the entire harness if necessary.
   • Ensure all connections are secure and properly insulated.
4. Check Thermistor/OWI Sensor:
   • If the wiring is intact, focus on the thermistor/OWI sensor.
   • Test the sensor for continuity using a multimeter. A lack of continuity indicates a faulty sensor.
5. Replace the Thermistor/OWI Sensor:
   • If the thermistor/OWI sensor is found to be faulty, replace it with a new, compatible component.
   • Ensure the replacement part is specifically designed for your KitchenAid dishwasher model.
6. Reconnect and Test:
   • After addressing the issues, reconnect the dishwasher to the power source.
   • Run a test cycle to check if the error code persists.

Kitchenaid Dishwasher Error Code 3-1 or F3E1

Kitchenaid Dishwasher Error Code 3-1 or F3E1

Error code 3-1 or F3E1 on your KitchenAid dishwasher signals a Thermistor and Optical Water Indicator (OWI) sensor failure. The thermistor is responsible for measuring water temperature, while the OWI sensor detects the level of debris in the water. When these crucial components malfunction, it can impact the dishwasher’s performance.

1. Faulty Thermistor: The thermistor, also known as the water temperature sensor, may experience a malfunction, leading to inaccurate temperature readings.
2. OWI Sensor Issues: The Optical Water Indicator sensor, designed to assess water quality, may fail to function correctly.
3. Wiring Problems: The wiring connecting the electronic control board to the thermistor/OWI sensor may be damaged or broken.

Troubleshooting Steps:

1. Unplug the Dishwasher:
   • Disconnect the dishwasher from the power source to ensure safety during troubleshooting.
2. Inspect Wiring:
   • Examine the wiring between the electronic control board and the thermistor/OWI sensor.
   • If you find any broken or damaged wires, repair or replace the wire harness.
3. Check Thermistor/OWI Sensor:
   • Inspect the thermistor and OWI sensor for visible damage or signs of wear.
   • If the components appear compromised, replacement is recommended.
4. Verify Temperature Settings:
   • Ensure that the dishwasher’s temperature settings are appropriate.
   • Adjust settings if necessary and run a test cycle to monitor for any improvements.
5. Professional Assistance:
   • If the issue persists after the above steps, or if you are unsure about component replacement, it is advisable to seek professional assistance.
   • Contact Appliance Repair Los Angeles at 323-792-1970 for expert help in diagnosing and resolving KitchenAid dishwasher error code 3-1 or F3E1.

Addressing thermistor and OWI sensor issues promptly is essential to maintain the efficiency of your KitchenAid dishwasher.

Kitchenaid Dishwasher Error Code 2-2 or F2E2

Kitchenaid Dishwasher Error Code 2-2 or F2E2

Error code 2-2 or F2E2 on your KitchenAid dishwasher signifies a communication breakdown between the user interface control and the electronic control board. This disruption in communication can impede the dishwasher’s normal operation, requiring prompt attention for resolution.

Possible Causes:

1. Wiring Issues: Faulty or damaged wiring between the user interface control and the electronic control board.
2. User Interface Control Board Malfunction: The user interface control board may be defective and unable to communicate with the electronic control board.
3. Electronic Control Board Failure: The electronic control board, a vital component overseeing dishwasher functions, may be malfunctioning.

Troubleshooting Steps:

1. Power Off and Inspection:
   • Turn off power to the dishwasher by unplugging it or switching off the circuit breaker.
   • Carefully inspect the wiring between the user interface control and the electronic control board for any visible damage or loose connections.
2. Check Wiring:
   • If any wiring issues are detected, address them by repairing or replacing the damaged wires. Ensure all connections are secure.
   • Pay close attention to the connections on both the user interface control and the electronic control board.
3. Replace User Interface Control Board:
   • If the wiring appears to be in good condition and the issue persists, consider replacing the user interface control board.
   • The user interface control board is responsible for receiving and transmitting commands; a malfunction could disrupt communication.
4. Replace Electronic Control Board:
   • If replacing the user interface control board doesn’t resolve the problem, the electronic control board may be faulty.
   • Consult your dishwasher’s manual for guidance on locating and replacing the electronic control board.

Error code 2-2 or F2E2 demands a thorough inspection of wiring and control boards. By following these steps, you can address the communication issue and restore your KitchenAid dishwasher to optimal functionality.

Kitchenaid Dishwasher Error Code 2-1 or F2E1

Kitchenaid Dishwasher Error Code 2-1 or F2E1

Error code 2-1 or F2E1 on your KitchenAid dishwasher signifies a potential issue with a stuck button on the user interface control. The user interface control is the panel with buttons and indicators that you interact with to set the dishwasher’s functions. When a button becomes unresponsive or stuck, it triggers this error code.

1. Check All Buttons on the User Interface:

   Manually inspect each button on the user interface control for any physical damage or sticking. Press each button to ensure a proper response.

2. Unplug the Dishwasher:

   Disconnect the dishwasher from the power source to ensure safety during troubleshooting.

3. Disconnect the User Interface Control Wire Harness:

   Locate and disconnect the wire harness connected to the user interface control. Reassemble the dishwasher door without closing it.

4. Plug in the Dishwasher and Wait:

   Plug the dishwasher back into the power source. Wait at least 7 seconds for the electronic control board to power up completely.

5. Close the Door:

   After the waiting period, close the dishwasher door.

6. Observe the Drain Pump:

   If the electronic control no longer detects stuck buttons with the user interface wire harness unplugged, it will initiate the drain pump. If the drain pump runs, it indicates a fault in the user interface control, and it should be replaced.

7. If Drain Pump Doesn’t Run:

   If the drain pump does not run, it suggests that the electronic control board still detects stuck buttons. In this case, replace the electronic control board.

If you find the troubleshooting steps challenging or if the error persists, it’s advisable to seek professional assistance.

Kitchenaid Dishwasher Error Code 1-2 or F1E2

Kitchenaid Dishwasher Error Code 1-2 or F1E2

When your KitchenAid dishwasher displays Error Code 1-2 or F1E2, it signifies a challenge with the appliance’s internal memory on the control board. This error is often associated with damaged or corrupted memory and the presence of incompatible software components within the microprocessor.

1. Damaged Control Board Memory: Over time, wear and tear or electrical issues may compromise the integrity of the control board’s memory.
2. Incompatible Software Components: An internal conflict within the microprocessor due to incompatible software components can trigger this error.

Troubleshooting Steps:

1. Power Cycle the Dishwasher:
   • Shut off power to the dishwasher by unplugging it or turning off the circuit breaker.
   • Allow the dishwasher to remain without power for at least 5 minutes.
2. Restore Power:
   • After the 5-minute interval, restore power to the dishwasher.
   • Observe if the error code reappears on the display.
3. Code Persistence:
   • If the error code returns upon restoring power, it indicates a persistent issue.
4. Professional Assessment:
   • Given the complex nature of control board-related errors, it is advisable to seek professional assistance.
5. Control Board Replacement:
   • If deemed necessary by the technician, replacing the electronic control board may be the ultimate solution.
   • A damaged control board may hinder the dishwasher’s performance and functionality.