Kenmore Dishwasher Error Code 6-6 or F6E6

Kenmore Dishwasher Error Code 6-6 or F6E6

When your Kenmore dishwasher displays the error code 6-6 or F6E6, it’s indicating that the incoming water is too cold. Understanding and addressing this issue is crucial to ensure your dishwasher operates efficiently. Here’s a more in-depth look at this error code and how to resolve it:

1. Check Water Temperature:

Use an accurate thermometer to measure the water temperature as it enters the dishwasher. It should ideally be around 120 degrees Fahrenheit (49 degrees Celsius) for optimal performance.
If the water temperature is significantly lower than 110 degrees F, you may want to inspect your water heater. Ensure it’s functioning correctly and set to an appropriate temperature.

2. Thermistor/OWI Check:

If your water temperature is within the normal range (110 to 120 degrees F), but you’re still seeing the error code, the issue may lie with the thermistor (also known as the OWI – Optical Water Indicator).
The thermistor is responsible for monitoring water temperature during the wash cycle. It sends this information to the electronic control board.

3. Replace the Thermistor/OWI or Electronic Control Board:

If you suspect the thermistor is the problem, you can consider replacing it. Refer to your dishwasher’s tech sheet or user manual for instructions on how to access and replace the thermistor.
Alternatively, if the thermistor appears to be in good condition, the issue might be with the electronic control board. Replacing the control board may resolve the error.

4. Diagnostic Test:

Some dishwashers offer a diagnostic test mode. Refer to the tech sheet that came with your dishwasher for instructions on how to perform this test. It can help confirm whether the thermistor is functioning correctly.

Seek Professional Assistance:

If you’re unsure about diagnosing and repairing the issue yourself, it’s always a good idea to contact a professional appliance repair technician. They have the experience and tools to accurately diagnose and fix problems with your dishwasher.

Don’t let a cold water error code disrupt your dishwashing routine. By addressing the issue promptly and accurately, you can ensure that your Kenmore dishwasher continues to provide clean and sanitary dishes after each cycle.

Kenmore Dishwasher Error Code 6-4 or F6E4

When your Kenmore dishwasher displays the error code 6-4 or F6E4, it’s telling you that the float switch is open. This error code indicates a potential issue with the dishwasher’s float switch mechanism. Here, we’ll delve deeper into this error and guide you through troubleshooting steps to help you resolve it.

The float switch is a crucial component in your dishwasher’s operation. It’s a small device located at the base of the dishwasher’s tub. The float, typically made of plastic, rises with the water level during the wash cycle. When the water reaches a certain level, the float activates the float switch, signaling to the dishwasher that it should stop filling with water. This prevents overfilling, which could lead to water damage in your kitchen.

Troubleshooting the 6-4 or F6E4 Error:

Here are steps to troubleshoot and potentially resolve the error:

1. Check for Blockages: Inspect the area around the float switch for any debris or foreign objects that might be preventing the float from moving freely. Even a small item under the float can trigger the error.

2. Ensure Proper Movement: Gently press down on the float to make sure it moves freely up and down. It should not be stuck in the up position, which would indicate a problem.

3. Inspect the Inlet Water Fill Valve: The error can also occur if the dishwasher’s water inlet valve isn’t shutting off properly when the dishwasher is turned off. To check this, you may need to turn off the water supply to the dishwasher and examine the valve for any leaks or malfunctions. It may require cleaning, repair, or replacement.

4. Power Cycle the Dishwasher: Sometimes, simply turning off the dishwasher, unplugging it, or shutting off its circuit breaker for a few minutes and then restarting it can reset the error code.

5. Consult Your Owner’s Manual: Your Kenmore dishwasher’s owner’s manual can be a valuable resource for troubleshooting specific error codes. It may offer additional guidance and information on your dishwasher’s float switch and inlet valve.

If you’ve gone through these troubleshooting steps and the 6-4 or F6E4 error persists, it’s a good idea to seek professional assistance. The issue may require advanced diagnostics, parts replacement, or adjustments that are best handled by a trained technician.

Kenmore Dishwasher Error Code 6-3 or F6E3

Check for sudsy water. If you see excessive suds, try to drain the dishwasher by cancelling the cycle. The drain pump will run for 3 minutes. If the drain pump can’t drain the sudsy water, drain the water by hand or use a wet/dry shop vacuum to remove the water. Check the detergent dispenser and replace if it’s damaged. Use only dishwasher detergent in the dishwasher. Using regular dish soap in the dishwasher causes excessive suds. If you don’t see excessive suds, check the water fill level in the tub because low water level causes air in the pump. The water level should just touch the bottom of the overfill float mushroom. If you find the water level too low, check for bowls or containers that flipped over during the cycle that could be holding water. Load items so they don’t flip over during the cycle and cause low water level. If you didn’t find bowls or containers flipped over and holding water, then a defective water inlet valve could cause the low water level. Unplug the dishwasher to disconnect electrical power and close the water supply valve. Disconnect the water supply line from the water inlet valve and check the water inlet valve screen for clogs. Replace the water valve if you find the screen clogged because debris from the clog can get into the valve body, causing the valve to stick open and possibly flood your kitchen. If the screen is clear, place the end of the water supply line in a shallow pan and briefly open the water supply valve to see if the water flows from the supply line. If water doesn’t flow, have a plumber repair the water supply to your dishwasher. If the water flows okay, check the wiring connections on the water inlet valve and reconnect any loose wires or replace the wire harness if damaged. If the wires are okay, you may need to replace the water inlet valve.

Kenmore Dishwasher Error Code 6-2 or F6E2

When your Kenmore dishwasher displays the error code 6-2 or F6E2, it’s signaling a water inlet valve failure. This error can disrupt the normal functioning of your dishwasher, but fear not – here’s how you can diagnose and potentially resolve the issue.

Step 1: Safety First

Before you begin any troubleshooting, ensure your safety by unplugging the dishwasher to disconnect it from electrical power. Safety should always be a top priority when working with appliances.

Step 2: Access the Bottom Front Panel

To access the components you need for inspection and potential repair, remove the bottom front access panel and toe panel of the dishwasher. These panels can typically be taken off with basic tools, like a screwdriver.

Step 3: Inspect Wire Harness Connections

Check the wire harness connections on the water inlet valve, which is often located near the front bottom of the dishwasher. Loose or disconnected wires can be a common culprit for this error. Reconnect any wires that may have come loose.

Step 4: Examine the Wire Harness

Inspect the wire harness for any signs of damage or wear. If you notice any frayed wires or other damage, it’s best to replace the wire harness to ensure a reliable connection.

Step 5: Test the Water Inlet Valve

Using a multimeter, check the resistance of the water inlet valve. You should measure around 1,400 ohms of resistance through the water inlet valve. If the multimeter shows infinite resistance, it’s a clear sign that the water inlet valve is faulty and needs replacement.

Step 6: Consider Replacing the Water Inlet Valve

If the resistance measurement indicates a problem with the water inlet valve, it’s wise to replace it. A malfunctioning valve can lead to insufficient water entering the dishwasher, hindering its performance.

Step 7: Potential Electronic Control Board Replacement

If, after following these steps, the problem persists, it might indicate a deeper issue with the dishwasher. In such cases, replacing the electronic control board could be necessary. This board is like the brains of the dishwasher, and if it’s malfunctioning, it can cause error codes like 6-2 or F6E2.

Remember that while these steps can help diagnose and potentially resolve the issue, some dishwasher repairs may require professional expertise. If you’re uncertain about any aspect of the process or if the problem persists after attempting these steps, don’t hesitate to contact a professional appliance repair service.

Kenmore Dishwasher Error Code 6-1 or F6E1

Your Kenmore dishwasher can sometimes display error codes like 6-1 or F6E1, indicating a specific issue with the appliance. In this article, we’ll explore the potential causes of this error code and provide you with comprehensive troubleshooting steps and solutions to resolve it.

This error code typically indicates a problem with the dishwasher’s ability to fill with water. Here’s what you can do to diagnose and address the issue:

1. Check for Overfill Float Obstruction:

The overfill float is a crucial component that can get stuck, preventing the dishwasher from filling with water. Inspect for any items lodged under the overfill float and remove them if found. This can often resolve the problem.

2. Unblock the Overfill Float:

If the overfill float is stuck in the “up” position, it can impede the dishwasher’s filling process. To correct this, unplug the dishwasher to disconnect it from electrical power and shut off the water supply valve.

3. Inspect the Water Inlet Valve:

Disconnect the water supply line from the water inlet valve and check the water inlet valve screen for clogs. If you find the screen clogged, debris from the clog can enter the valve body, causing the valve to stick open and potentially lead to a kitchen flood. In this case, it’s advisable to replace the water valve.

4. Verify Water Supply:

If the screen is clear and there are no issues with the water inlet valve, place the end of the water supply line in a shallow pan and briefly open the water supply valve to check if water flows from the supply line. If water doesn’t flow, you might need to have a plumber repair the water supply to your dishwasher.

5. Inspect Wiring Connections:

Check the wiring connections on the water inlet valve. If you find any loose wires, reconnect them securely. If the wires are damaged, consider replacing the wire harness.

6. Potential Component Replacement:

If all the above steps don’t resolve the issue, you may need to consider replacing the water inlet valve or the electronic control board, as one of these components might be malfunctioning.

By following these troubleshooting steps, you can often identify and rectify the issue causing the Kenmore dishwasher error code 6-1 or F6E1. However, if you’re uncertain about performing these tasks or if the problem persists, it’s advisable to contact a professional appliance repair technician.

Kenmore Dishwasher Error Code 5-2 or F5E2

The Kenmore dishwasher error code 5-2 or F5E2 indicates that the control panel has detected a problem related to the dishwasher door not opening as expected. The electronic control board in your dishwasher anticipates that the door will be opened between cycles. If it doesn’t detect the door being opened, it may prevent the dishwasher from starting the next cycle.

Steps to Resolve the Error:

Cancel the Cycle: If you receive this error code and haven’t opened the door between cycles, the first step is to cancel the current cycle. The control board expects this action.
Open and Shut the Door: After canceling the cycle, open and close the dishwasher door firmly. This action signals to the control board that the door has been opened and closed, as it should be between cycles.
Attempt a New Cycle: After opening and closing the door, start a new cycle. This should reset the control board and allow the dishwasher to operate without errors.

If the Error Persists:

If, after following the above steps, the error code 5-2 or F5E2 continues to appear, it may indicate a problem with the door switch or latch assembly. Here’s how to proceed:

Unplug the Dishwasher: To further diagnose the issue, unplug the dishwasher from the power source. This will ensure your safety during the following steps.
Simulate Door Opening: After unplugging, plug the dishwasher back in. This simulates the door opening, and the control board should recognize this as the door being opened.
Start a Cycle: Attempt to start a new cycle. If the cycle starts without the error code, this suggests that the control board is working as expected. However, if the error persists, it indicates that the door switch is not detecting the door’s status accurately.
Replace the Door Latch Assembly: If the error persists after simulating the door opening, it’s advisable to replace the door latch assembly. The door switch within this assembly may be defective, causing the control board to receive incorrect signals.

Resolving the Kenmore dishwasher error code 5-2 or F5E2 is essential to ensure that your dishwasher operates smoothly. Following these steps can often help you address the issue without the need for professional repair. However, if the error code continues to be a problem, it’s advisable to consult with an appliance technician to diagnose and resolve the underlying issue, ensuring your dishwasher works reliably and efficiently.

Kenmore Dishwasher Error Code 5-1 or F5E1

When it comes to Kenmore dishwasher error codes, understanding what they mean and how to address them is essential to keep your appliance running smoothly. Error code 5-1 or F5E1, which indicates a door switch failure, is a common issue you might encounter. Let’s delve deeper into this error code and explore the steps to resolve it.

Error code 5-1 or F5E1 is displayed when you fail to close the dishwasher door within 4 seconds of pressing the Start/Resume button or if the door latch assembly is malfunctioning.

How to Resolve Kenmore Dishwasher Error Code 5-1 or F5E1:

Quick Start/Resume: To avoid this error, ensure that when you press the Start/Resume button, you close the dishwasher door within 4 seconds. This quick action is essential to initiate the cycle properly.
Check the Door Switch Wire Harness:
- First, unplug the dishwasher to disconnect electrical power. Safety is a priority when working on appliances.
- Disassemble the door of your dishwasher to access the door switch and its wire harness.
- Examine the wire harness for any loose or disconnected wires. Reconnect them securely.
Inspect the Door Latch Assembly:
- If the error persists and the wire harness appears intact, it’s time to inspect the door latch assembly.
- The door latch assembly is the mechanism that keeps the dishwasher door securely closed during a cycle.
- If you find any issues with the latch assembly, such as visible damage or a lack of functionality, it should be replaced.

Kenmore Dishwasher Error Code 4-2 or F4E2

Error codes on your Kenmore dishwasher can be perplexing, but they often hold the key to identifying and resolving specific issues. In this article, we’ll delve deeper into one common error code: 4-2 (or F4E2), which signifies a communication error between the electronic control board and the circulation pump motor. We’ll explore the potential causes and step-by-step solutions to help you address this issue and get your dishwasher back in working order.

This error code, 4-2 or F4E2, on your Kenmore dishwasher points to a communication breakdown between the electronic control board and the circulation pump motor. This breakdown can result from various factors, including loose or damaged wiring, or potential issues with the control board or pump motor itself.

Safety First: Before attempting any repairs, ensure your dishwasher is unplugged to disconnect electrical power.
Inspect the Circulation Pump Wire Harness:
- Carefully examine the wire harness connected to the circulation pump motor. Look for loose or disconnected wires.
- If you find any loose wires, reconnect them securely. Ensure all connections are tight and well-seated.
Assess Wire Harness Damage:
- If the wire harness is visibly damaged, it’s crucial to replace it. Damaged wiring can impede communication and proper functioning.
Replacing the Circulation Pump and Motor Assembly:
- If the wiring connections are intact, but the error persists, it may be necessary to replace the circulation pump and motor assembly.
- Seek the guidance of your Kenmore dishwasher’s user manual for specific instructions on safely replacing this component. If you’re uncomfortable with this task, consider enlisting the help of a professional technician.
Replacing the Electronic Control Board:
- If the issue continues after replacing the pump and motor assembly, the electronic control board may be at fault.
- Consult your user manual for guidance on replacing the control board, or contact a professional technician to handle this task safely.

Remember, tackling error code 4-2 (F4E2) can be complex, especially when it involves replacing essential components. If you’re unsure or uncomfortable with any of the above steps, it’s wise to seek professional assistance to ensure the problem is diagnosed and resolved accurately.

Kenmore Dishwasher Error Code 4-1 or F4E1

The Kenmore Dishwasher Error Code 4-1 or F4E1 signifies a communication error between the electronic control board and the circulation pump motor. When this error occurs, your dishwasher may not function correctly, and it’s important to address it promptly.

Troubleshooting the Error:

1. Unplug the Dishwasher:

Safety first. Before you start any troubleshooting, ensure that your dishwasher is unplugged or disconnected from the electrical power source.

2. Check the Circulation Pump Wire Harness:

Open up your dishwasher to access the internal components.
Inspect the circulation pump wire harness for loose or disconnected wires. Reconnect any loose wires if you find them.

3. Replace the Wire Harness (if damaged):

If you discover that the wire harness is damaged, it’s essential to replace it. A damaged wire harness can disrupt communication between the control board and the pump motor.

4. Replace the Circulation Pump and Motor Assembly:

If the wiring connections are in good condition, but the error persists, it’s time to consider replacing the circulation pump and motor assembly. This assembly includes the pump and motor that help circulate water in the dishwasher.

5. Consider Replacing the Electronic Control Board:

If the problem continues even after replacing the circulation pump and motor assembly, it may be necessary to replace the electronic control board. The control board is responsible for coordinating various functions in your dishwasher, and a communication error could indicate a fault in this component.

Seeking Professional Help: While the steps above outline a systematic approach to troubleshoot and resolve Kenmore Dishwasher Error Code 4-1 or F4E1, it’s important to note that some dishwasher repairs can be complex. If you’re unsure about your technical skills or if the problem persists after attempting these solutions, it’s advisable to seek professional assistance.

Kenmore Dishwasher Error Code 3-3 or F3E3

Error codes on your Kenmore dishwasher can be frustrating, but understanding them and knowing how to troubleshoot can save you time and money on repairs. In this guide, we’ll dive deeper into the Kenmore Dishwasher Error Code 3-3 or F3E3 and explore the steps to address it.

Understanding Error Code 3-3 or F3E3:

This error code typically points to two potential issues:

OWI Calibration Failure: The Optical Water Indicator (OWI) sensor failed to calibrate correctly. This sensor measures the level of soil in the water to determine how long the dishwasher cycle should run.
Drain Hose Check Valve Failure: The check valve in the drain hose failed, allowing dirty water to backflow into the dishwasher. This can result in poor cleaning and potential contamination of your dishes.

Troubleshooting Steps:

Check the Drain Hose:
- First, disconnect the dishwasher drain hose connection from the air gap or the garbage disposal (if you have no air gap).
- Pour water through the drain hose to see if water backs up into the dishwasher tub. If you notice backflow, it’s a clear indication of a failed check valve in the drain hose.
Replace the Drain Hose:
- If water backs up into the dishwasher, it’s time to replace the portion of the drain hose that connects to the drain pump. This will resolve the check valve issue and prevent further backflow.
OWI Sensor Calibration:
- If water doesn’t back up into the dishwasher through the drain hose, reconnect the hose.
- Run the Service Diagnostics Test according to the instructions in the tech sheet. During this test, ensure that you see “low soil level” indicated. This signifies the proper calibration of the OWI sensor in the diagnostic mode.
OWI Sensor Maintenance:
- If the OWI test shows “high soil level,” it indicates that the OWI sensor might be dirty or malfunctioning. In this case, unplug the dishwasher and clean the OWI sensor carefully.
- Reassemble the dishwasher, plug it back in to restore electrical power, and run the diagnostic test cycle. This will allow the electronic control board to calibrate the OWI sensor correctly on the next cycle.
Run a Normal Wash Cycle:
- After the calibration and sensor maintenance, run a normal wash cycle to see if the error code reappears.
Replace the Thermistor/OWI Sensor:
- If you still encounter the error code after performing the above steps, it may be necessary to replace the thermistor/OWI sensor.

By following these troubleshooting steps, you can address Kenmore Dishwasher Error Code 3-3 or F3E3 and ensure your dishwasher is back to running smoothly and efficiently. If you’re unsure about any step or if the issue persists, consider seeking professional appliance repair assistance.