GE Washer Error Code: E70

GE Washer Error Code: E70

Your GE washer is a workhorse, tirelessly handling the dirty laundry. But occasionally, even the most reliable appliances can throw a curveball in the form of error codes. If you’ve encountered the E70 error code on your GE washer, don’t panic. We’re here to help you understand and resolve this issue.

The E70 error code is an indicator of a specific problem in your washer. It typically points to an issue related to the control board. When the control board detects an anomaly, such as a malfunction or a communication breakdown, it triggers the E70 error code.

Unplug the Washer: The first step in addressing the E70 error is to unplug the washer from the power source. Leave it unplugged for at least 3 minutes. This action serves to reset the control board.
Plug the Washer Back In: After the 3-minute reset, plug the washer back into the power source. Power it on and observe if the error code returns. In some cases, a simple power cycle can resolve the issue.
Replacing the Control Panel: If the E70 error code persists after the reset, it’s likely that the control panel is the culprit. The control panel is responsible for receiving and transmitting commands to the washer’s components. If it’s malfunctioning or experiencing a communication breakdown, replacement may be necessary.

GE Washer Error Code: E66 or E67

E66 and E67 error codes are associated with the water level sensor and water temperature sensor, respectively. These sensors play a crucial role in the proper functioning of your washer. When they malfunction, they can trigger these error codes, indicating that it’s time to address the issue.

Safety First: Unplug your GE washer to ensure your safety while performing any troubleshooting or repairs.
Check Wiring Connections: Examine the wiring connections on the water level sensor. Loose or disconnected wires can result in these error codes. Reconnect any wires that are not securely fastened.
Inspect Wire Harness: If the wiring connections appear intact and secure, inspect the wire harness for any visible damage or wear. A damaged wire harness can disrupt the sensor’s communication with the washer’s control board. If you find damage, it’s advisable to replace the wire harness.
Replace Sensor: If the wiring connections and wire harness are in good condition, but the error codes persist, the next step is to replace the faulty sensor. For the E66 error code, replace the water level sensor, and for the E67 error code, replace the water temperature sensor. This replacement is necessary to restore the sensor’s functionality and clear the error codes.

GE Washer Error Code: E65

When your GE washer displays error code E65, it’s signaling an issue related to the water level control system. This can occur for various reasons, including problems with the pressure switch, the hose connecting the switch, or the main control board. In essence, the washer is having difficulty determining the water level in the drum, which can impede its ability to function correctly.

Run the T06 Water Level Control Test: A useful first step in addressing error code E65 is to run the T06 water level control test. This test helps diagnose whether the issue lies with the water level control components or other parts of the washer. Follow your washer’s user manual for instructions on running this test. If the test reveals no issues with the water level control system, the problem might be related to the main control board.
Inspect the Pressure Switch and Hose: Check the pressure switch, which is responsible for sensing the water level in the drum. Ensure that it’s properly connected and functioning. Also, inspect the hose that connects to the pressure switch for any blockages or damage.
Replace the Main Control Board: If the T06 test indicates no problems with the water level control system, and you’ve ruled out issues with the pressure switch and hose, it may be time to consider replacing the main control board. This component is central to your washer’s operation and may need replacement if it’s malfunctioning.

While some error codes can be resolved with DIY efforts, others, like E65, may require the expertise of a professional technician. If you’re uncertain about the diagnosis or uncomfortable with replacing components, it’s best to contact a reliable appliance repair service.

GE Washer Error Code: E60, E61, E63 or E64

These error codes, E60, E61, E63, and E64, are related to the door lock assembly of your GE washer. They typically indicate issues with the door lock or its associated components. When these error codes appear, the washer is signaling a problem with the door lock mechanism, which plays a crucial role in ensuring the door remains securely closed during operation.

Inspect the Door Lock Assembly: Begin by visually inspecting the door lock assembly. Check for any visible signs of damage, such as cracks or broken parts. Ensure that the latch is in good condition and properly aligned.
Check for Loose Wiring: It’s not uncommon for wiring connections to become loose over time due to vibrations and movement. Carefully examine the wiring harness connected to the door lock assembly. If you find any loose or disconnected wires, securely reattach them.
Test the Door Lock Mechanism: To confirm if the issue lies with the door lock assembly, perform a simple test. Close the washer door and attempt to start a cycle. If the door lock doesn’t engage, or if it disengages shortly after starting, this indicates a problem with the door lock.

GE Washer Error Code: E57 or E58

E57 and E58 error codes indicate a malfunction in your GE washer’s main control board. The control board serves as the “brain” of the appliance, coordinating various functions to ensure your washer operates smoothly. When this essential component fails to perform correctly, it triggers these error codes to alert you to the issue.

Power Cycle: Sometimes, electronic glitches can cause false error codes. Start by turning off your washer, unplugging it, and waiting a few minutes before plugging it back in. This power cycle can sometimes reset the control board and clear the error code.
Inspect Wiring and Connections: Ensure that all wiring and connections to the control board are secure and free from damage. Loose or damaged connections can sometimes cause control board errors.
Software Update: In some cases, a software update or reset might resolve control board issues. Refer to your washer’s user manual for instructions on how to update the firmware.

GE Washer Error Code: E48

E48 is an error code that pertains to an issue with the drive motor of your GE washer. This component is crucial for the functioning of the machine, as it’s responsible for powering the drum’s movement during the wash and spin cycles. When the washer’s control unit detects a problem with the drive motor, it generates the E48 error code as a signal for attention.

Safety First: Before you embark on any troubleshooting, ensure your safety by unplugging the washer from the electrical outlet. This prevents any electrical hazards while working on the appliance.
Check for Loose Wiring: In many cases, the E48 error may be triggered by loose or disconnected wiring connections to the drive motor. Examine the wires and harnesses, making sure they are securely connected to the motor. Reconnect any loose wires you find.
Inspect the Wiring: Thoroughly examine the wiring for signs of damage, such as fraying or exposed wires. If any wiring is compromised, it should be replaced. Damaged wiring can not only trigger error codes but also pose safety risks.
Replace the Drive Motor: If you’ve checked the wiring connections and they appear to be in good condition, and the error code persists, it’s likely that the drive motor itself is faulty. In this case, the drive motor will need to be replaced.

GE Washer Error Code: E47

When your GE washer displays E47 on its digital display, it’s trying to tell you that there’s a problem with the drive motor. More specifically, it often points to loose wiring connections or a malfunctioning drive motor. This issue can lead to an overheat in the inverter control board, causing the machine to hit pause.

Unplug and Reconnect: The first thing you should do is unplug the washer from the power source. Safety always comes first. Once it’s safe, inspect the wiring connections to the drive motor. If any of these connections are loose or disconnected, reattach them securely.
Replace the Drive Motor: If the wiring connections appear to be in good shape, the next step is to consider the drive motor. A malfunctioning drive motor can indeed cause the inverter control board to overheat, which in turn triggers the E47 error. Replacing the drive motor is often the solution in this case.
Inverter Control Board Replacement: In the rare event that the problem persists even after replacing the drive motor, it may be time to address the inverter control board. A defective inverter control board can cause various issues in your washer, and the E47 error is one of them.

GE Washer Error Code: E46

Error Code E46 in your GE washer points to a problem with the drive motor. When the machine detects an issue with the motor or its connections, it will display E46 to alert you. This issue could interrupt the washer’s operation, causing frustration when you’re in the middle of your laundry chores.

Safety First: As a preliminary step, ensure the washer is unplugged from the power source. Safety should always come first when dealing with electrical appliances.
Check Wiring Connections: The E46 error code often indicates an issue with the wiring connections to the drive motor. Carefully inspect all wiring connections to the motor. Look for any loose, disconnected, or damaged wires. Ensure they are securely connected and in good condition.
Reconnect Loose Wiring: If you find any loose or disconnected wires, reattach them to the drive motor. Make sure the connections are snug and secure.
Replace Drive Motor: If the wiring connections appear to be in good condition, but the error code persists, it may be necessary to replace the drive motor. A malfunctioning drive motor can lead to the E46 error code and disrupt the washer’s operation. It’s a more complex repair, and it’s advisable to seek the assistance of a professional technician for motor replacement.

GE Washer Error Code: E43

The E43 error code signifies that the main control board of your GE washer has detected a defect in the inverter control board. This inverter control board plays a crucial role in managing the speed of the drive motor, which is integral to the washer’s operation. When this board encounters an issue, it triggers the E43 error code.

Unplug the Washer: As a first step, unplug the washer from the power source. This ensures your safety while working on the appliance.
Check Wiring Connections: Examine the wiring connections between the main control board and the inverter control board. Loose or damaged wires can cause communication errors and lead to the E43 code. Reconnect any loose wires and ensure they are securely in place.
Inspect the Inverter Control Board: Carefully examine the inverter control board for visible damage or signs of overheating. If the board appears burnt, charred, or damaged, it’s a clear indication that it needs replacement.
Replace the Inverter Control Board: If the inverter control board is indeed faulty, the recommended solution is to replace it. To do this, consult your GE washer’s user manual for specific instructions or seek the assistance of a professional technician.

GE Washer Error Code: E42 or E45

E42 and E45 on your GE washer indicate motor-related errors. These errors can be attributed to problems with the inverter or the motor itself. They’re essentially your washer’s way of saying, “Houston, we have a motor problem.

Clear the Error Code: When you see E42 or E45 on your display, the first step is to clear the error code. To do this, exit any service mode or diagnostic setting on your washer.
Power Down for 30 Seconds: Once you’ve cleared the code and exited the service mode, disconnect the power to your washer. It’s crucial to leave it unplugged for at least 30 seconds. This pause allows the washer’s control system to reset.

A Note of Caution:

While it’s essential to disconnect the power to reset the control system, make sure you follow the proper sequence. Exiting the service mode before disconnecting the power is crucial. Failing to do so may potentially damage the control system.