GE Dishwasher Error Code: FTD or F56

GE Dishwasher Error Code: FTD or F56

The dishwasher did not drain. Check the drain hose, air gap, and disposer.

Check for a blockage:

Make sure there is not any paper or large object covering or blocking the sump area in the rear of the tub. Clear out any large pieces of food from the bottom of the dishwasher like noodles, lettuce, bones, etc.
Check the drain hose where it connects below the sink for a blockage or a kink in the hose. New dishwashers come with a white corrugated drain hose which should be used. Re-using old, worn out drain hoses may promote kinking or a blockage.
Make sure the kitchen sink drain is not clogged. If a disposer is installed, run the disposer to clear the drain system. Do not put your hands into the garbage disposer to check it as a serious injury could occur. You should always turn on your garbage disposer prior to running the dishwasher to clean out any food or debris within the drain system.
If an air gap is installed with the dishwasher drain plumbing, remove the cap on the air gap and clean out any build-up of debris. Clearing the air gap will allow water to flow better as the dishwasher drains.
If a disposer was recently installed or replaced, make sure the drain plug inside the disposer was removed. Instructions for removing the drain plug are in the disposer’s installation instructions.

GE Dishwasher Error Code: Cup Open

When you encounter the GE Dishwasher error code “Cup Open,” it signifies a specific issue. Here’s a detailed guide on what this error code means and how to address it:

1. Understanding Error Code “Cup Open”: The “Cup Open” error code indicates that the dishwasher has detected an issue with the detergent cup’s closure or position. The dishwasher’s sensor is unable to confirm the proper closure of the detergent cup, and this can prevent the wash cycle from starting.

2. Override and Start the Cycle: If you receive the “Cup Open” error code and the cycle doesn’t begin, you can attempt to override it:

Without opening the dishwasher door, press the start pad again. This action can sometimes bypass the error code and initiate the wash cycle.

3. Monitor for Persistence: After attempting the override, monitor the dishwasher’s operation. Ensure that the wash cycle proceeds without any further issues. If the error code “Cup Open” persists and prevents the dishwasher from functioning correctly, it’s an indicator of a more significant issue that requires attention.

GE Dishwasher Error Code: PF Code

When you encounter the GE Dishwasher error code PF, it indicates a power failure. This code usually appears when the dishwasher loses power during a cycle or when power is restored after an outage. Here’s a detailed guide on what this error code means and how to address it:

1. Power Failure During a Cycle: If your dishwasher displays the PF error code due to a power failure during a cycle, here’s what to do:

Simply select the desired cycle and options as usual.
Press the Start pad, and the dishwasher will resume and function normally.

The PF error code is essentially a reminder to restart the cycle after a power interruption. The dishwasher retains your selected cycle and options, so there’s no need to reprogram it from the beginning. This feature ensures convenience and efficiency.

2. Power Restoration After Outage: In the case of a power outage that has been restored, you may see the PF error code. Here’s how to address it:

Select the cycle and options you want to run.
Press the Start pad, and the dishwasher will initiate the selected cycle. The dishwasher is ready to continue its operation after power is restored.

3. Prevention Tips: While power failures are beyond your control, you can consider some preventive measures:

Using surge protectors or uninterruptible power supplies (UPS) for your appliances can help protect them from sudden power surges or outages.
Regularly backing up dishwasher settings or noting the cycle and options used can be helpful in case a power failure occurs.

By following these steps, you can effectively address GE Dishwasher error code PF (Power Failure). The dishwasher is designed to make it easy for you to resume operation after a power interruption, ensuring your dishwashing process remains hassle-free and convenient.

GE Dishwasher Error Code: C8

When your GE dishwasher displays error code C8, it typically points to an issue with the detergent dispenser. Here’s a detailed guide on what this error code signifies and how to address it:

1. Remove Blockage in Dispenser Cover: If you encounter error code C8, the first step is to check and remove any obstructions in the detergent dispenser cover. Follow these steps:

Inspect the detergent dispenser cover carefully for any objects or residue that may be preventing it from opening properly.
Remove any blockages, debris, or buildup that could be interfering with the cover’s functionality.

2. Restart the Dishwasher: After ensuring the detergent dispenser cover is free from obstructions, shut the cover securely and restart a wash cycle on the dishwasher.

3. Monitor the Dispenser Cover: Approximately 20-30 seconds into the wash cycle, check to see if the detergent dispenser cover opens as it should. It should release the detergent at the appropriate time during the cycle. If it opens as expected, the problem is resolved. If the cover remains closed or malfunctioning, continue with the following steps.

4. Replace the Detergent Dispenser: If the detergent dispenser cover does not open as it should or the detergent dispenser itself is broken or damaged, it may need replacement. Follow these steps:

Identify the specific model of your GE dishwasher to ensure you order the correct replacement part.
Obtain a new Detergent Dispenser Assembly as a replacement part.
Carefully remove the damaged or malfunctioning detergent dispenser from your dishwasher.
Install the new Detergent Dispenser Assembly in its place according to the manufacturer’s instructions.

By following these troubleshooting and replacement steps, you can effectively address GE Dishwasher error code C8. Ensure that you use the correct replacement part for your specific dishwasher model to ensure smooth and efficient detergent dispensing during your dishwasher’s cycles.

GE Dishwasher Error Code: C7

Error code C7 in your GE dishwasher indicates a potential issue with the water temperature sensor or the electronic control board. Here’s a detailed guide on what this error code means and how to address it:

1. Remove Power and Reset: The first step when encountering error code C7 is to remove power from the dishwasher for approximately 5 minutes. This action is an attempt to reset the electronic control board. Follow these steps:

Unplug the dishwasher or turn off its power source to ensure it is completely disconnected.
Wait for about 5 minutes to allow the electronic control board to reset.
After this period, plug the dishwasher back into power and observe if error code C7 reappears.

2. Check for Loose Wire Connections: If the error code C7 persists after the power reset, it’s time to inspect the water temperature sensor’s wire connections. Loose or faulty connections could be the cause. Here’s what to do:

Disconnect power to the dishwasher to ensure safety during inspection.
Access the water temperature sensor and examine its wiring harness. Make sure all connections are secure. If you find any loose or damaged wires, address them accordingly.

3. Replace the Water Temperature Sensor: If the wiring harness is secure and there are no issues with the connections, the next step is to consider replacing the water temperature sensor. A malfunctioning sensor could trigger error code C7.

4. Replace the Electronic Control Board: If, after troubleshooting and replacing the water temperature sensor, the error code C7 persists, it may indicate a problem with the electronic control board. In this case, replacing the electronic control board is necessary.

GE Dishwasher Error Code: C6

Water temperature coming into the dishwasher should be at least 120 degrees F. Run the faucet adjacent to the dishwasher prior to starting the dishwasher to purge any cold water from the line. Adjust the water heater temperature. Don’t use the washing machine or take showers when using the dishwasher. Use options on the dishwasher to cause the machine to run longer and thus add more heat.

GE Dishwasher Error Code: C5

Be sure the water supply valve to the dishwasher is completely open. Be sure the overfill float switch is not stuck in the up position as this will prevent the dishwasher from filling with water. Remove the dishwasher from power and turn off the water supply valve. Remove the water fill line and check the water inlet valve. If the inlet screen is blocked or has clogs then replace the water inlet valve as only cleaning the screens is not enough and can cause flooding. Check the wiring harness on the water inlet valve to be sure there are no loose wires. If you find that the water inlet valve does not open when power is applied then replace it.

GE Dishwasher Error Code: C4

Error code C4 in your GE dishwasher indicates drainage issues. Here’s a detailed guide on what this error code means and how to address it:

1. Dishwasher Will Not Drain After Cancelling: If your dishwasher is not draining after you’ve canceled a wash cycle, it can be a cause for concern. Follow these steps to troubleshoot the issue:

First, refer to the C3 error code troubleshooting guide mentioned above. Reset the dishwasher’s power using the circuit breaker as instructed in the C3 guide and check if this clears the problem. It might resolve any temporary glitches.

2. Dishwasher Drains After Cancelling Wash Cycle: If the dishwasher does drain after canceling the wash cycle, it suggests a different issue. Check for the following:

Examine if there is anything lodged underneath the overfill float. The overfill float is a safety device that can be obstructed, causing drainage problems. Remove any obstructions carefully if found.

3. Inspect Overfill Float Switch: If nothing is lodged under the overfill float and the dishwasher still doesn’t drain correctly, it’s time to examine the overfill float switch. Follow these steps:

Disconnect power to the dishwasher to ensure safety during inspection.
Inspect the overfill float switch for proper operation. If you notice any damage, such as a malfunctioning switch, it’s advisable to replace it with a new one.

4. Replacement Parts: Based on your findings and the condition of your dishwasher, you might need to consider replacing certain components:

Drain Pump: If the pump is damaged or not functioning correctly, a replacement may be necessary.
Drain Hose: Check the drain hose for clogs or damage. If it’s compromised, consider replacing it.
Overfill Float Switch: As mentioned, if the overfill float switch is damaged or malfunctioning, it should be replaced with a new one.

By following these troubleshooting steps and replacing any faulty components, you can effectively address GE Dishwasher error code C4. For the replacement parts mentioned, consult your dishwasher’s manual or a professional technician for the correct parts and installation process to ensure your dishwasher operates efficiently.

GE Dishwasher Error Code: C3

GE Dishwasher error code C3 can be an indication of underlying issues with your appliance. Here’s a detailed guide on what this error code means and how to address it:

1. Disconnect Power and Reset: The first step when encountering error code C3 is to disconnect the power to the dishwasher at the circuit breaker. This helps to perform a complete reset of the dishwasher. Follow these steps:

Locate your home’s electrical circuit breaker panel.
Find the circuit breaker that controls power to your dishwasher and switch it to the “off” position. Ensure the dishwasher is completely disconnected from power.

Allow the dishwasher to remain disconnected for about 30 seconds. This time allows the dishwasher’s control board to reset and clear any temporary glitches.

After 30 seconds, switch the circuit breaker back to the “on” position, providing power to the dishwasher again.
Turn on the dishwasher and observe if the error code C3 is cleared.

2. Monitor for Persistence: Once you’ve reset the dishwasher, monitor its operation for some time. Ensure it completes its cycles without displaying the error code. If the problem persists and error code C3 reappears, it may indicate an underlying issue with the appliance that requires professional service.

3. Contact Service: If error code C3 continues to be displayed after the power reset and you’ve ensured the dishwasher is properly installed and all connections are secure, it’s advisable to contact a service technician. This error code could point to more complex electrical or control board issues that require expert diagnosis and repair.

GE Dishwasher Error Code: C2

C2 – Drain Line Totally Blocked – This error will occur when dishwasher is unable to pump out water within the maximum time of 405 seconds. Check drain line and drain valve in pump for debris and blockage. Note: If a new garbage disposal has been installed, remove knock out plug for dishwasher drain.