Electrolux Refrigerator is producing a burning smell
Electrolux Refrigerator Light Bulb
Make sure the light is not staying on when the door is closed. A regular incandescent bulb can get hot and produce a burning smell.
Electrolux Refrigerator Compressor
The compressor start device, also known as a start relay or start relay and overload kit, may have failed. This will usually cause the compressor to not start. If the burning smell is coming from the compresser area check the start device. If the start device smells burnt, or the compressor is trying to start but can’t, the start device is likely bad and will need to be replaced.
Electrolux Refrigerator Power Cord
Inspect the power cord prongs and wall receptacle for burn marks. The cord should plug tightly into the receptacle. A power cord that is hot is a sign of a bad connection. If the power cord is burnt or damaged it will need to be replaced. If the cord is loose in the receptacle, the receptacle will need to be replaced by a licensed electrician.
Electrolux Refrigerator Condenser Fan Motor
If the burning smell appears to be coming from the exterior of the refrigerator, it’s possible the condenser fan motor is wearing out or overheating. You should inspect the component for any burn marks, especially near the wire connection points, and use a multimeter to test the motor for electrical continuity to help determine if the component has burned out.
Electrolux Refrigerator Wire Connector
Inspect the wiring and connectors in the area of the smell. A bad connection or pinched or shorted wire can produce a burning smell.
Electrolux Refrigerator Control Board
If one of the components has failed it can produce a burning smell from that area. Look for a stuck fan motor or a shorted control board.
Electrolux Refrigerator Light Switch
A regular incandescent bulb can get hot and produce a burning smell, especially if the light switch has shorted closed leaving the light illuminated even with the refrigerator door closed. You can use a multimeter to test the light switch for electrical continuity. If the switch has continuity both before and after the switch has been actuated, it has shorted closed and will need to be replaced.
Electrolux Refrigerator Door Switch
A regular incandescent bulb can get hot and produce a burning smell, especially if the door switch has shorted closed leaving the light illuminated even with the refrigerator door closed. You can use a multimeter to test the door switch for electrical continuity. If the switch has continuity both before and after the switch has been actuated, it has shorted closed and will need to be replaced.
Electrolux Refrigerator Evaporator Fan Motor
If the evaporator fan blade won’t turn, the motor windings can overheat and produce a burning smell. You should confirm the fan blade can turn freely and replace the evaporator fan motor if defective.
Electrolux Refrigerator Start Device
A start device, like a start relay, works in conjunction with the start winding to start the compressor. If the start device has shorted, it can overheat and produce a burning smell. Inspect the start device for any damage and replace if necessary.
Electrolux Refrigerator Main Control Board
If the main control board has shorted it can produced a burning smell. You can inspect the board for any burn damage and replace if necessary.
Electrolux Refrigerator ice maker not working
01 – Electrolux Refrigerator Main Control Board
The refrigerator’s main control board controls the voltage being sent to the ice maker. If the control board is defective, the ice maker may not work at all. You can inspect the board for signs of damage or a shorted component. You can also use a multimeter to determine if voltage is reaching the ice maker after reviewing the refrigerator’s wiring diagram.
02 – Freezer Temperature is Above 10 Degrees F (-12C)
If the freezer temperature is above 10 degrees Fahrenheit (-12C), the ice maker will not produce ice cubes efficiently. The freezer temperature should be set between 0 and 5 degrees Fahrenheit (-18 to -15C) for the ice maker to work properly. If the freezer temperature is too high, ensure that the condenser coils are clear of debris and the condenser fan is working properly. In addition, check to see if frost has accumulated on the evaporator coils. If the evaporator coils are frosted over, part of the defrost system has likely failed.
03 – Electrolux Refrigerator Water Inlet Valve
The water inlet valve is an electrically-controlled valve that opens to supply water to the dispenser and ice maker. If the water inlet valve is defective, or if it has insufficient pressure, it won’t allow water to flow through. As a result, the ice maker won’t make ice. The valve requires at least 20 psi to function properly. Make sure that the water pressure to the valve is at least 20 psi. If the water pressure is sufficient, use a multimeter to check for power to the water inlet valve. If the water inlet valve has sufficient pressure and is getting power, but the ice maker won’t fill with water to make ice, replace the water inlet valve.
04 – Electrolux Refrigerator Ice Maker Assembly
One component of the ice maker assembly might be defective. Since many of the ice maker components are not sold separately, you may need to purchase and replace the entire ice maker assembly. Before replacing the ice maker assembly, check the water inlet valve, water line, and fan. If none of these parts are at fault, and the freezer temperature is at least 15 degrees Fahrenheit, replace the ice maker assembly.
05 – Electrolux Refrigerator Fill Hose
If there is low water pressure coming into the refrigerator, or the water inlet valve is defective, the ice maker’s fill tube can become clogged with ice and prevent water from entering the ice maker tray. You can use a hair dryer to thaw out the frozen fill tube, but you should confirm the home has sufficient water pressure and the water inlet valve is functioning properly. If the fill tube appears damaged, you should replace it with a new fill tube.
06 – Low Water Pressure from House Supply
The home may have insufficient water pressure. The water inlet valve supplies water to the ice and water dispenser. The water inlet valve requires a minimum of 20 psi to function properly. Check the water flow and test the pressure to determine if it is at least 20 psi.
07 – Confirm icemaker is On
Make sure the icemaker is turned on and the arm or paddle is able to move freely. On in-door ice-dispensing models, with the door open make sure the indicator light stays on steadily when the ice dispenser flap and door switch are pressed.
08 – Frozen fill tube on ice maker
If there is low water pressure coming into the refrigerator, or the water inlet valve is defective, the ice maker’s fill tube can become clogged with ice and prevent water from entering the ice maker tray. You can use a hair dryer to thaw out the frozen fill tube, but you should confirm the home has sufficient water pressure and the water inlet valve is functioning properly.
09 – Electrolux Refrigerator Door Switch
The door switch turns off the ice and water dispenser when the refrigerator door is open. If the door switch fails, the dispenser will not turn on. To determine if the door switch is defective, use a multimeter to test it for continuity. If the door switch does not have continuity when activated, replace it.
10 – Electrolux Refrigerator Ice Level Control Board
On some refrigerator models, an ice level control board and sensor will be used to determine how much ice is in the ice bucket. When the ice bucket fills to capacity, the ice level control board will automatically shut off the power to the ice maker. If the ice level control board is malfunctioning, it may not allow the ice maker to turn on at all. If the refrigerator has an in-door ice dispenser, open the door and check to see if the indicator light stays on steadily when the ice dispenser paddle and door switch are pressed. If not, the ice level control board is likely defective.
11 – Electrolux Refrigerator Control Board
The refrigerator’s control board controls the voltage being sent to the ice maker. If the control board is defective, the ice maker may not work at all. You can inspect the board for signs of damage or a shorted component. You can also use a multimeter to determine if voltage is reaching the ice maker after reviewing the refrigerator’s wiring diagram.
12 – Electrolux Refrigerator Icemaker Fill Tube Heater
The fill tube heater keeps the fill tube warm, to help prevent ice buildup, and keep water flowing to the icemaker.
13 – Electrolux Refrigerator Water Filter
A clogged water filter can restrict the flow of water to the dispenser and prevent the ice maker from working properly. The water filter should be replaced about every six months to maintain proper water flow and ensure water quality.
Electrolux Refrigerator ice is dirty
01 – Electrolux Refrigerator Water Supply Tube
During normal use the water supply tubes will have water flowing through them keeping them clean. If the water supply gets disconnected or water is left in the tube and not used for 6 to 12 months, it can become discolored. If the water at the other faucets in the house is ok and you have replaced the water filter you may need to replace the water tubing to the ice maker to resolve the issue.
02 – Electrolux Refrigerator Ice Maker Assembly
If the icemaker tray has a coating, the coating may be wearing off. If you are getting pieces or chunks of material stuck in the ice, check the ice maker tray. If the coating on the tray is corroded and flaking off, replace the icemaker.
03 – Dirty Water Supply
The water supplied to the house may be dirty. The ice maker uses the same water as the faucet. Often, a fire hydrant that was flushed or a broken water main can cause dirty water. In these cases, you should run the water for awhile at the faucet to clear out the lines and discard the ice until the water clears up.
04 – Electrolux Refrigerator Water Filter
If the ice being dispensed is dirty, it’s possible that residue from an old water filter is getting into the water being supplied to the ice maker. Water filters should be replaced every six months for optimum water filtration.
Electrolux Refrigerator ice maker overflowing
Electrolux Refrigerator Water Inlet Valve
The water inlet valve requires a minimum of 20 psi to shut off properly. If the water pressure is too low, the valve may not close fully once the power is shut off. As a result, the valve will leak water into the ice maker and cause the ice maker to overflow. Check the water pressure to determine if it is at least 20 psi. If the water pressure is sufficient, the water inlet valve is likely defective. The valve may not shut off all the way or may be stuck open, causing water to leak through the valve. If the water pressure is sufficient, but the ice maker is still overflowing, replace the water inlet valve.
Obstructed Ice Maker
If there are food items stuck in or jammed around the icemaker, it may not cycle properly. The ice maker may get stuck in the middle of a cycle or overflow with ice or water. Inspect the icemaker and remove any items that may interfere with its operation.
Low Water Pressure from House Supply
The water inlet valve supplies water to the refrigerator ice and water dispenser. The valve requires a minimum of 20psi to work properly. If the water pressure is too low, the valve may not close fully when the power is shut off. As a result, the valve leaks water into the ice maker, causing it to overflow. Check the water flow and test the pressure to determine if it is at least 20 psi.
Electrolux Refrigerator Ice Maker Assembly
One component of the ice maker assembly might be defective. Since many of the ice maker components are not sold separately, you may need to purchase and replace the entire ice maker assembly.
Electrolux Refrigerator ice and water dispenser not working
Electrolux Refrigerator Dispenser Actuator
The dispenser actuator is the component that activates the switch or switches to send voltage to the dispenser. If the dispenser actuator is damaged, it may be unable to activate the switch. Inspect the dispenser actuator for any damage and replace with a new one if necessary.
Electrolux Refrigerator Dispenser Control Board
The dispenser control board governs most of the functions of the dispenser system. If only one dispenser part is not working, it is probable that an individual part has failed. In this case, test each of the dispenser components before testing the control board. If the entire dispenser system is not working, the control board is more likely to be at fault.
Electrolux Refrigerator Dispenser Switch
The dispenser switches send voltage to the dispenser. If one of the dispenser switches is defective, the dispenser will not work. To determine if a dispenser switch is defective, use a multimeter to test each switch for continuity. If a dispenser switch does not have continuity, replace it.
Electrolux Refrigerator Door Switch
The door switch turns off the ice and water dispenser when the refrigerator door is open. If the door switch fails, the dispenser will not turn on. To determine if the door switch is defective, use a multimeter to test it for continuity. If the door switch does not have continuity when activated, replace it.
Doors not closing properly
Check to make sure all drawers and ice buckets are pushed in properly. Be sure the refrigerator doors are completely closed. There should be no visible gap around the door gasket.
Electrolux Refrigerator Water Filter Housing
On many refrigerators, the incoming water will pass through a water filter before reaching the dispenser or the ice maker fill tube. If the water filter housing is damaged, water may not flow through the housing when the filter is installed. Inspect the water filter housing for damage and confirm it is properly seated. If necessary replace the damaged housing with a new one.
Electrolux Refrigerator Main Control Board
The main control board might be defective. However, the control board is rarely at fault for this problem. Before replacing the control board, first check all of the dispenser components. If none of the dispenser components are defective, consider replacing the main control board.
Electrolux Refrigerator Ice Maker Assembly
If just the refrigerator’s ice dispenser is not working, you should first confirm that the ice maker assembly is functioning properly and producing ice. Since many of the ice maker components are not sold separately, you may need to purchase and replace the entire ice maker assembly. Before replacing the ice maker assembly, check the water inlet valve, water line, and fan. If none of these parts are at fault, and the freezer temperature is at least 15 degrees Fahrenheit, replace the ice maker assembly.
Electrolux Refrigerator Water Inlet Valve
A refrigerator water inlet valve will direct water to the dispenser as well as the ice maker fill tube. If the inlet valve is obstructed, the solenoid coils on the valve are defective, or the home’s water pressure is too low, the water valve will not work properly. The valve requires at least 20psi to function properly. Make sure that the water pressure to the valve is at least 20 psi. If the water pressure is sufficient, use a multimeter to test the water inlet valve for continuity. If the water inlet valve does not have continuity, replace it.
Electrolux Refrigerator has frost or moisture buildup around the door
Electrolux Refrigerator Mullion Heater
A defective mullion heater flap may not be able to heat up periodically to melt any frost or moisture that forms on the flap due to increases in room humidity. You can use a multimeter to test the mullion heater for electrical continuity to determine if the component is working. If the mullion heater has no electrical continuity you should replace it with a new one.
Electrolux Refrigerator Door Support
If the mullion heater flap has frost or moisture buildup, it’s possible the door suport is damaged or misaligned and not allowing the flap to form a tight seal between the refrigerator doors. Inspect the door support for wear or damage and replace if necessary.
Electrolux Refrigerator Door Guide
If the mullion heater flap has frost or moisture buildup, it’s possible the door guide is damaged or misaligned and not allowing the flap to form a tight seal between the refrigerator doors. Inspect the door guide for wear or damage and replace if necessary.
Electrolux Refrigerator Door Gasket
A door gasket should form an airtight seal around the appliance’s frame to keep the cold air in and the warm air out. If the door gasket is twisted or torn, gaps can form that will allow warm air in, resulting in the freezer not freezing properly. Inspect the door gasket for any damage and replace with a new one if necessary.
Refrigerator or freezer door left open
If the freezer or refrigerator door was left open for an extended period of time (e.g. more than 4 hours), frost may have accumulated on the food, evaporator coil and around the door opening. The frost should go away after the door is closed and the refrigerator goes through a defrost cycle.
Electrolux Refrigerator has frost or ice buildup
Electrolux Refrigerator Defrost Control Board
The defrost control board determines how often to run the defrost cycle. If the board fails, the refrigerator will not go into the defrost cycle. Before replacing the defrost control board, first test the defrost heater and defrost thermostat. If the defrost heater and defrost thermostat are working properly, the defrost control board is likely defective.
Electrolux Refrigerator Defrost Timer
The defrost timer turns on the defrost heater several times throughout the day to melt any frost that may have accumulated on the evaporator coils. If the defrost timer is defective, it may not advance into the defrost cycle, or it may not send power to the defrost heater during the defrost cycle. To determine if the defrost timer is defective, slowly advance the dial into the defrost cycle. The compressor should turn off and the heater should turn on. If the timer does not send power to the defrost components or advance out of the defrost cycle within 30 minutes, this indicates that the defrost timer is not advancing. If the defrost timer is not advancing, replace it.
Electrolux Refrigerator Water Inlet Valve
The water inlet valve requires a minimum of 20 psi to shut off properly. If the water pressure is too low, the valve may not close fully once the power is shut off. As a result, the valve will leak water into the ice maker and cause the ice maker to overflow. Check the water pressure to determine if it is at least 20 psi. If the water pressure is sufficient, the water inlet valve is likely defective. The valve may not shut off all the way or may be stuck open, causing water to leak through the valve. If the water pressure is sufficient, but the ice maker is still overflowing, replace the water inlet valve.
Electrolux Refrigerator Fan Motor
If the refrigerator’s defrost drain is clogged, it’s possible the evaporator fan motor is not working. If the evaporator fan is not running, cold air from the evaporator can migrate to the defrost drain causing ice buildup in the drain. To determine if the evaporator fan motor is defective, try turning the fan blade by hand. If the fan blade does not turn freely, replace the fan motor. Additionally, if the motor is unusually noisy, replace it. Finally, if the motor does not run at all, use a multimeter to test the motor windings for continuity. If the windings do not have continuity, replace the evaporator fan motor.
Electrolux Refrigerator Drain Strap
Some defrost drains are outfitted with a drain strap. The drain strap is a small piece of copper or aluminum that attaches to the defrost heater and extends partway into the defrost drain. When the defrost heater turns on, heat is conducted through the drain strap to melt away any ice that may have accumulated further down in the defrost drain. If the drain strap is not in place, the defrost drain may be more likely to freeze over.
Electrolux Refrigerator Evaporator Fan Motor
If the refrigerator’s defrost drain is clogged, it’s possible the evaporator fan motor is not working. If the evaporator fan is not running, cold air from the evaporator can migrate to the defrost drain causing ice buildup in the drain. To determine if the evaporator fan motor is defective, try turning the fan blade by hand. If the fan blade does not turn freely, replace the fan motor. Additionally, if the motor is unusually noisy, replace it. Finally, if the motor does not run at all, use a multimeter to test the motor windings for continuity. If the windings do not have continuity, replace the evaporator fan motor.
Electrolux Refrigerator Drain Heater
Some refrigerators are equipped with drain heaters. Drain heaters prevent the water in the drain pan from re-freezing and clogging the defrost drain. If your drain heater is defective or is not in the proper position, the defrost drain might freeze over.
Electrolux Refrigerator Ice Maker Assembly
One component of the ice maker assembly might be defective. Since many of the ice maker components are not sold separately, you may need to purchase and replace the entire ice maker assembly.
Electrolux Refrigerator Auger Motor
The auger motor spins the auger blade and pushes the ice through the dispenser chute. If the auger motor is burned out or defective, the ice won’t move forward and fall through the chute. To determine if the auger motor is defective, pull out the ice bucket and turn the bucket auger by hand. If the auger turns freely, use a multimeter to test the auger motor for continuity. If the auger motor does not have continuity, or if the motor is getting power but won’t run, replace the auger motor.
Electrolux Refrigerator Defrost Heater Assembly
The defrost heater assembly turns on several times throughout the day to melt away any frost that may have accumulated on the evaporator coils. If the defrost heater assembly is defective, the defrost system will not work, and frost will continue to accumulate on the evaporator coils. To determine if the defrost heater is defective, use a multimeter to test it for continuity. If the defrost heater does not have continuity, replace it.
Electrolux Refrigerator Defrost Thermostat
The defrost thermostat monitors the temperature of the evaporator coils. When the coils drop below a set temperature, the thermostat contacts close to allow power to flow to the defrost heater during the defrost cycle. In the defrost cycle, the defrost heater melts away any frost that may have accumulated on the evaporator coils. If the defrost thermostat is defective, the thermostat contacts will not close. As a result, the thermostat won’t provide power to the defrost heater. To determine if the defrost thermostat is defective, use a multimeter to test it for continuity. If the defrost thermostat does not have continuity when it reaches the low temperature of its operating range, replace it.
Electrolux Refrigerator Thermistor
A thermistor monitors the temperature of the evaporator coils. If the coils are below a set temperature, the thermistor will alert the defrost control to allow power to flow to the defrost heater during the defrost cycle. In the defrost cycle, the defrost heater melts away any frost that may have accumulated on the evaporator coils. If the thermistor is defective, the defrost control will not be alerted to allow voltage to be sent to the defrost heater.
Electrolux Refrigerator Defrost Sensor with Fuse
The defrost sensor monitors the temperature of the evaporator. The defrost sensor has a fuse to back up the sensor in case the sensor fails. If the defrost sensor fails to shut off the defrost heater, the fuse will blow in order to shut off the defrost heater. If the defrost sensor fuse blows, the defrost system will not work, and the refrigerator will not defrost. The defrost sensor fuse is not resettable—if the defrost sensor fuse blows, you must replace the defrost sensor. To determine if the defrost sensor or fuse is defective, use a multimeter to test both the sensor and fuse for continuity. If either the defrost sensor or fuse does not have continuity, replace the defrost sensor.
Electrolux Refrigerator Main Control Board
The main control board regulates the power supply to all of the refrigerator components, including the defrost system. If the main control board is defective, it may stop sending voltage to the defrost system. Control boards are frequently misdiagnosed—before replacing the main control, first test all of the defrost system components. If none of the defrost system components are defective, consider replacing the main control board.
Electrolux Refrigerator Control Board
The control board regulates the power supply to all of the refrigerator components, including the defrost system. If the main control board is defective, it may stop sending voltage to the defrost system. Control boards are frequently misdiagnosed—before replacing the main control, first test all of the defrost system components. If none of the defrost system components are defective, consider replacing the control board.
Electrolux Refrigerator Mullion Heater
French door refrigerators will often use a mullion heater flap which flips open as the two main doors are closed to provide a proper seal. If the mullion heater is misaligned or damaged, it can prevent the doors from closing properly. Inspect the mullion heater for any damage and replace it with a new one if necessary.
Electrolux Refrigerator Door Support
A refrigerator door support is often used on French Door models to flip a mullion heater flap to seal the gap between the doors. If the door support is damaged or misaligned, the mullion heater flap may not be positioned appropriately for the door or doors to close completely. Inspect the support for damage and replace if necessary.
Electrolux Refrigerator Door Guide
A door guide is often used on French door refrigerators to assist in flipping open a mullion heater flap to provide a seal between the two main doors. If the guide is damaged or misaligned, the flap may not engage accurately and prevent the doors from closing properly. Inspect the door guide (often attached to the inner liner at the top of the frame) and replace it with a new one if necessary.
Electrolux Refrigerator Temperature Sensor
A temperature sensor monitors the temperature of the evaporator coils. If the coils are below a set temperature, the sensor will alert the defrost control to allow power to flow to the defrost heater during the defrost cycle. In the defrost cycle, the defrost heater melts away any frost that may have accumulated on the evaporator coils. If the temperature sensor is defective, the defrost control will not be alerted to allow voltage to be sent to the defrost heater.
Electrolux Refrigerator freezing food
Electrolux Refrigerator Temperature Control Thermostat
The temperature control thermostat directs voltage to the compressor, evaporator fan motor, and condenser fan motor (if applicable). If the temperature control thermostat is not working properly, it may cause the refrigerant system to run longer than necessary. As a result, the refrigerator will be too cold. To determine if the thermostat is defective, rotate the thermostat from the lowest setting to the highest setting and listen for a click. If the thermostat clicks, it is not likely defective. If the thermostat does not click, use a multimeter to test the thermostat for continuity. If the temperature control thermostat does not have continuity at any setting, replace it.
Electrolux Refrigerator Thermistor
The thermistor monitors the air temperature and sends the temperature reading to the control board. The control board then regulates power to the compressor and evaporator fan based on the thermistor readings. If the thermistor is defective, the compressor and evaporator fan may run too frequently. As a result, the refrigerator will be too cool. To determine if the thermistor is defective, test it with a multimeter. The thermistor resistance should change in conjunction with the refrigerator temperature. If the thermistor resistance does not change, or the thermistor does not have continuity, replace the thermistor.
Electrolux Refrigerator Temperature Control Board
The temperature control board provides voltage to the compressor and fan motors. If the control board is faulty, it may send continuous voltage to the compressor or fan motors. As a result, the refrigerator will be too cool. Control boards are often misdiagnosed—before replacing the control board, first test all of the more commonly defective components. If none of the other components are defective, consider replacing the temperature control board.
Electrolux Refrigerator Main Control Board
The main control board might be defective. However, the control board is very rarely the cause of the problem. Before replacing the control board, first test all of the more commonly defective components. If none of these components are defective, consider replacing the main control board.
Temperature set too cold
Adjust the refrigerator temperature control to a warmer setting. Many models have a recommended temperature setting displayed, usually between 34 and 38 degrees Fahrenheit. Wait 24 hours for the temperature to adjust appropriately.
Electrolux Refrigerator Evaporator Fan Motor
The refrigerator’s evaporator fan motor draws air over the cold evaporator coils which chills the air. The air is then circulated through the refrigerator and freezer compartments to keep the temperature low enough to preserve food. If the evaporator fan motor is malfunctioning, the cold air from the freezer or refrigerator evaporator coils can migrate through the air ducts to the bottom of the refrigerator and freeze the food. You should try rotating the evaporator fan blades to see if they spin freely. If not, it’s likely the motor bearings have seized and the motor will need to be replaced. You can also use a multimeter to test the motor for electrical continuity. If the motor has no electrical continuity, the component won’t run and a new motor will need to be installed.
Food Items too close to the vents
Allow space between the air vents and the food. If certain foods are directly in front of the cold air vent they can freeze.
Electrolux Refrigerator Control Board
The control board might be defective. However, the control board is very rarely the cause of the problem. Before replacing the control board, first test all of the more commonly defective components. If none of these components are defective, consider replacing the main control board.
Electrolux Refrigerator Damper Control Assembly
The air damper control opens and closes to let the proper amount of cold air into the refrigerator compartment. If the damper does not close properly, it will let too much cold air into the refrigerator. Check the damper control to determine if it is broken or stuck open.
Electrolux Refrigerator Damper
The damper opens and closes to let the proper amount of cold air into the refrigerator compartment. If the damper is stuck open, it will let too much cold air into the refrigerator. As a result, the refrigerator will be too cold. Check the damper to determine if it is broken or stuck open.
Electrolux Refrigerator Temperature Sensor
The temperature sensor monitors the refrigerator temperature and signals the control board to direct voltage to the compressor, evaporator fan motor, and condenser fan motor (if applicable) to restart the cooling system when necessary. If the temperature sensor is not working properly, it may cause the refrigerant system to run longer than necessary. As a result, the refrigerator will be too cold. You can often use a multimeter to test the sensor for changes in resistance as the sensor is heated up or cooled down. If the component shows no changes in resistance, the sensor is faulty and should be replaced.
Electrolux Refrigerator freezer not freezing
Electrolux Refrigerator Evaporator Fan Motor
The evaporator fan motor draws air over the evaporator (cooling) coils and circulates it throughout the refrigerator and freezer compartments. Some refrigerators have more than one evaporator fan motor. On refrigerators with two evaporators, there will be an evaporator located in both the freezer and refrigerator compartments. If the evaporator fan is not working, it will not circulate the cold air in the compartment. If this occurs, the refrigerator may still get cold, while the freezer will not get cold or vice versa. To determine if the evaporator fan motor is defective, try turning the fan blade by hand. If the fan blade does not turn freely, replace the fan motor. Additionally, if the motor is unusually noisy, replace it. Finally, if the motor does not run at all, use a multimeter to test the motor windings for continuity. If the windings do not have continuity, replace the evaporator fan motor.
Electrolux Refrigerator Door Gasket
A freezer door gasket should form an airtight seal around the appliance’s frame to keep the cold air in and the warm air out. If the door gasket is twisted or torn, gaps can form that will allow warm air in, resulting in the freezer not freezing properly. Inspect the door gasket for any damage and replace with a new one if necessary.
Electrolux Refrigerator Condenser Fan Motor
The condenser fan motor draws air though the condenser coils and over the compressor. If the condenser fan motor is not working properly, the refrigerator won’t cool properly. To determine if the fan motor is defective, first check the fan blade for obstructions. Next, try turning the fan motor blade by hand. If the blade does not spin freely, replace the condenser fan motor. If no obstructions are present and the fan blade spins freely, use a multimeter to test the fan motor for continuity. If the condenser fan motor does not have continuity, replace it.
Electrolux Refrigerator Control Board
Control boards are often misdiagnosed—before replacing the control board, first check more commonly defective parts. If you have determined that all of the other components are working properly, replace the control board.
Electrolux Refrigerator Temperature Control Thermostat
The temperature control thermostat directs voltage to the compressor, evaporator fan motor, and condenser fan motor (if applicable). If the temperature control thermostat is not working properly, it may prevent the freezer’s refrigerant system from running. To determine if the thermostat is defective, rotate the thermostat from the lowest setting to the highest setting and listen for a click. If the thermostat clicks, it is not likely defective. If the thermostat does not click, use a multimeter to test the thermostat for continuity. If the temperature control thermostat does not have continuity at any setting, replace it.
Electrolux Refrigerator Start Relay
The start relay works in conjunction with the start winding to start the compressor. If the start relay is defective, the compressor may sometimes fail to run or may not run at all. As a result, the freezer will not be able to freeze properly. To determine if the start relay is defective, use a multimeter to test it for continuity between the run and start terminal sockets. If the start relay does not have continuity between the run and start terminal sockets, replace it. In addition, if the start relay has a burnt odor, replace it.
Electrolux Refrigerator Start Device
A start device, like a start relay, works in conjunction with the start winding to start the compressor. If the start device is defective, the compressor may sometimes fail to run or may not run at all. As a result, the freezer won’t be able to freeze. To determine if the start device is defective, use a multimeter to test it for continuity between the run and start terminal sockets. If the start device does not have continuity between the run and start terminal sockets, replace it. In addition, if the start device has a burnt odor, replace it.
Electrolux Refrigerator Inverter Board
The inverter board controls the power to the compressor. The main control board monitors the temperatures in the refrigerator and freezer compartments and sends signals to the inverter board. The inverter board varies the compressor speed depending on temperature change and run time.
Electrolux Refrigerator Main Control Board
The main control board monitors the compartment temperatures and sends power to the various components when needed. Control boards are often misdiagnosed. If a part is not working, test the part first before replacing the board.
Electrolux Refrigerator Compressor
The compressor is a pump which compresses the refrigerant and circulates the refrigerant through the evaporator and condenser coils. If the compressor is not working, the refrigerator won’t cool. However, this is rarely the case. Before replacing the compressor, first check all of the more commonly defective parts. If you have determined that all of the other components are working properly, check the compressor. Use a multimeter to test the continuity between the electrical pins on the side of the compressor. If there is an open circuit, the compressor is likely defective. If the compressor is defective, it must be replaced by a licensed technician.
Electrolux Refrigerator Reversing Valve
The reversing valve switches the flow of the refrigerant between the refrigerator and freezer evaporator coils on a dual evaporator system. If the reversing valve is not working properly both the refrigerator and freezer temperatures can be affected.
Electrolux Refrigerator Thermistor
The thermistor monitors the freezer temperature and sends the temperature reading to the control board. The control board regulates power to the compressor and evaporator fan based on the thermistor readings. If the thermistor is defective, the compressor and evaporator fan may not run when necessary. As a result, the freezer will not be cold enough. To determine if the thermistor is defective, test it with a multimeter. The thermistor resistance should change in conjunction with the refrigerator temperature. If the thermistor resistance does not change, or the thermistor does not have continuity, replace the thermistor.
Freezer or refrigerator temperature is set too high
Verify the freezer temperature is set between 0 and 5 degrees Fahrenheit (-18 to -15 Celsius). Verify the refrigerator temperature is set between 34 and 40 degrees Fahrenheit (1 to 5 Celsius). After reseting the temperature wait 24 hours for the temperature to adjust appropriately.
Electrolux Refrigerator freezer door or drawer not closing properly
Electrolux Refrigerator Door Hinge
A damaged or bent door hinge could cause the freezer door to be misaligned and not close properly. Inspect the hinge for defects and replace if necessary.
Electrolux Refrigerator Door Stop
A damaged refrigerator freezer door stop can prevent the door from closing properly. Inspect the component for signs of wear and replace if necessary.
Electrolux Refrigerator Center Hinge
A damaged or bent center hinge could cause the freezer door to be misaligned and not close properly. Inspect the hinge for defects and replace if necessary.
Electrolux Refrigerator Door Hinge Kit
A damaged or bent door hinge could cause the freezer door to be misaligned and not close properly. Inspect the hinge for defects and install new door hinge kit components if necessary.
Electrolux Refrigerator Hinge
A damaged or bent hinge could cause the freezer door to be misaligned and not close properly. Inspect all hinges for defects and replace one or more as necessary.
Obstructed Door
The freezer’s door may not be able to close properly if a shelf or drawer is misaligned or large food items are stored in a door bin. Confirm all shelves are in place and drawers fully closed, and rearrange food items as necessary, to remove any obstruction preventing the door from fully closing and sealing.
Electrolux Refrigerator Closing Cam
A refrigerator door closing cam allows the door to rest in place in the open position and to close securely on its own when the door is swung shut. A damaged closing cam could prevent the door from closing properly. Inspect the cam for wear or damage and replace if necessary.
Electrolux Refrigerator Closing Mechanism
A refrigerator door closing mechanism allows the door to rest in place in the open position and to close securely on its own when the door is swung shut. A damaged closing mechanism could prevent the door from closing properly. Inspect the mechanism for wear or damage and replace if necessary.
Electrolux Refrigerator Drawer Slide Rail
The drawer slide rails allow a freezer drawer to slide easily in and out. If either of the slide rails is damaged or misaligned, the drawer may not close properly. Inspect the slide rails for wear or damage and replace if necessary.
Electrolux Refrigerator Drawer Track
The drawer tracks allow a freezer drawer to slide easily in and out. If either of the tracks is damaged or misaligned, the drawer may not close properly. Inspect the tracks for wear or damage and replace if necessary.
Electrolux Refrigerator Door Gasket
A twisted or worn gasket can keep the door from closing properly. Inspect the door gasket for kinks or twists. You can use a hair dryer to try smoothing out the kinks. If the door gasket is damaged it will need to be replaced.
