Electrolux Dishwasher making noise
Electrolux Dishwasher Drain Pump
First, check the drain pump to ensure that it is clear of debris. If the drain pump is clean but it is still noisy, replace it.
Electrolux Dishwasher Circulation Pump
The circulation pump motor has bearings that wear out over time. When the motor bearings fail, they generate a continuous drone. If the motor bearings have failed, you must replace the entire circulation pump.
Electrolux Dishwasher Drain Impeller
The drain impeller pushes water through the drain hose and into the garbage disposer or drain line. If the impeller is broken, replace it.
Electrolux Dishwasher Pump and Motor Assembly
Part of the pump and motor assembly (such as the motor bearings, drain impeller, or wash impeller) might be defective. Often, you can replace the pump’s individual parts. However, if you do not want to disassemble the pump to replace its parts, or if the parts are not available separately, you can replace the entire pump and motor assembly.
Electrolux Dishwasher Wash Impeller
The wash impeller is a small plastic blade that forces water through the spray arms. If one or more of the impeller blades is broken, the dishwasher will make noise. In addition, if the impeller is damaged, warped, or bent, it can scape against the pump housing. Inspect the wash impeller for damage. If the wash impeller is damaged, replace it. On most models, you can replace the wash impeller independently of the pump and motor assembly. Search for your model number to determine if your impeller is replaceable. If the impeller cannot be replaced separately, you will have to replace the entire pump and motor assembly.
Electrolux Dishwasher Circulation and Drain Pump Motor
The circulation pump motor has bearings that wear out over time. When the motor bearings fail, they generate a continuous drone. If the motor bearings have failed, replace the motor or replace the entire pump and motor assembly.
Obstructed wash arm
There are several wash arms in a dishwasher, typically one for each rack. If a handle or untensil is sticking through one of the racks the wash arm may be hitting it as it turns. Or there may be an item that is too tall and obstructing the upper wash arm. Confirm that nothing is obstructing the upper or lower wash arms.
Electrolux Dishwasher Water Inlet Valve
The water inlet valve opens to allow water to enter the dishwasher. When it is new, the water inlet valve is very quiet during operation. Over time, the diaphragm inside the valve deteriorates and deforms. This deformation interacts with the water rushing in and can produce a loud vibration, buzzing, squealing, or other noises. If the dishwasher is loud during the filling cycle, replacing the water inlet valve may solve the problem.
Electrolux Dishwasher Circulation Pump Motor
If the noise is happening only during the wash cycle, it’s quite likely a worn out circulation pump motor is the cause. The circulation pump motor has an impeller and bearings that can wear out over time. When the motor bearings fail, they generate a continuous drone. If the impeller is broken or damaged, it will produce a grinding noise. If either the bearings or impeller are damaged, you must replace the entire circulation pump.
Electrolux Dishwasher won’t fill
01 – Electrolux Dishwasher Water Inlet Valve
The water inlet valve opens to allow water to enter the dishwasher. If the water valve is clogged or defective, water will not flow into the dishwasher. Water inlet valves are not repairable—if the valve is defective, you must replace it.
02 – Electrolux Dishwasher Main Control Board
A dishwasher’s main control board provides power to nearly every electrical component in the dishwasher. A faulty board may be unable to supply power to the water inlet valve, preventing it from opening and allowing the necessary water to fill the tank.
03 – Electrolux Dishwasher Float Switch
The float switch is a safety designed to shut off the water inlet valve if the dishwasher is overfilling. If the float switch is defective or stuck, it might stop the dishwasher from filling correctly. You can use a multi meter to test the float switch for continuity. If the float switch is defective, replace it.
04 – Electrolux Dishwasher Control Board
A dishwasher’s control board provides power to nearly every electrical component in the dishwasher. A faulty board may be unable to supply power to the water inlet valve, preventing it from opening and allowing the necessary water to fill the tank.
05 – Water Supply Problem
Over time, calcium deposits can build up in the water supply valve or in the small filter screen inside the water inlet valve. If the water inlet valve is clogged with sediments, the dishwasher won’t fill properly. Before working on the water line, first shut off the water supply. Inspect the valve to determine if it is clogged. In addition, check the water pressure to the valve. The water inlet valve requires at least 20 psi to function properly.
06 – Electrolux Dishwasher Pressure Switch
A dishwasher pressure switch is the component that will send a signal to shut off the water inlet valve once an appropriate amount of water has entered the tank for a wash cycle. If the pressure switch is malfunctioning, it may prevent the inlet valve from opening and filling the tank. You can use a multimeter to test the pressure switch’s terminals for appropriate changes in electrical continuity before and after blowing air into the attached pressure tube. If the switch does not test appropriately, it should be replaced.
Electrolux Dishwasher dispenser not dispensing soap
01 – Electrolux Dishwasher Dispenser Lever
If the dishwasher dispenser lever is broken, it can cause the dispenser not to open or close properly. Inspect the dispenser lever for damage. If the lever is broken, replace it.
02 – Electrolux Dishwasher Detergent Dispenser Cover
Inspect the dispenser cover for damage. If the dispenser cover is broken, replace it.
03 – Electrolux Dishwasher Control Board
The control board provides power to nearly every component of the dishwasher. If there is a problem with the control board, it might not send voltage to the detergent dispenser, preventing the dispenser from opening. However, this is not likely the case. Control boards are often misdiagnosed—make sure you check more commonly defective parts before replacing the control board
04 – Electrolux Dishwasher Detergent Container
Inspect the dishwasher detergent container for damage. If the detergent container is broken or damaged, replace it.
05 – Electrolux Dishwasher Dispenser Lid
Inspect the lid for damage. If the dispenser lid is broken or damaged, replace it.
06 – Electrolux Dishwasher Detergent Dispenser
If a dispenser part is broken and you don’t want to disassemble the detergent dispenser to replace the part, you can replace the entire dispenser.
07 – Electrolux Dishwasher Dispenser Door Spring
If the dispenser door spring is defective, the dispenser might not open during the wash cycle. Inspect the dispenser door spring for damage. If it is bent, broken, or damaged in any way, replace it.
08 – Electrolux Dishwasher Dispenser Latch
If the dispenser latch is defective, the dispenser won’t open or close properly. Inspect the dispenser door latch for damage. If the latch is damaged, replace it.
09 – Electrolux Dishwasher Dispenser Door Pin
If the dispenser door pin is defective, the dispenser won’t open or close properly. Inspect the dispenser door pin for damage. If the pin is damaged, replace it.
10 – Electrolux Dishwasher Dispenser Actuator
If the dispenser actuator is defective, the dispenser won’t open or close properly. Inspect the dispenser actuator for damage. If the dispenser actuator is damaged, replace it.
11 – Electrolux Dishwasher Dispenser
If you don’t want to disassemble the dispenser to replace a part, you can replace the entire dispenser. Additionally, if the dispenser isn’t working and the entire dispenser is worn out, replace the dispenser.
12 – Electrolux Dishwasher Bi-Metal
The bi-metal actuator is a metal loop which acts as a latch for the dispenser door. As electricity is applied to the bi-metal, it deforms and bends away from the latch, releasing it. If the bi-metal is burned out, it won’t release the dispenser door. To determine if the bi-metal has burned out, use a multimeter to test it for continuity. If the bi-metal does not have continuity, replace it. In addition, make sure that the dishwasher is getting enough water. If the water level is too low, the wash motor may not draw enough current through the bimetal, causing the bimetal not to bend enough to work properly.
13 – Electrolux Dishwasher Dispenser Slide
If the dispenser slide is damaged, the dispenser won’t open or close properly. If the slide is broken or damaged, replace it.
14 – Electrolux Dishwasher Pump and Motor Assembly
The dishwasher’s pump and motor assembly circulates the water through the wash arms during the wash and rinse cycles. If the pump and motor assembly is defective, the wash cycle may be interrupted and the dispenser will not be activated to release the detergent. In this case, the pump and motor assembly will need to be replaced.
15 – Improper loading
There needs to be adequate space between the dishes and the dispenser. Inadquate space can prevent the dispenser door from opening or prevent water from mixing with the detergent. If a large item is placed in front of the dispenser the detergent will not get rinsed out properly. Leave some space between the dishes and don’t place large plates or pans in front of the dispenser.
16 – Electrolux Dishwasher Water Inlet Valve
A dishwasher’s water inlet valve opens following a short drain cycle to fill the tank with water in preparation for the wash cycle. If the inlet valve is faulty and the tank does not fill, the wash cycle may be interrupted and the dispenser will not be activated to release the detergent. In this case, the water inlet valve will need to be replaced.
17 – Electrolux Dishwasher Main Control Board
The main control board provides power to nearly every component of the dishwasher. If there is a problem with the main control board, it might not send voltage to the detergent dispenser, preventing the dispenser from opening. However, this is not likely the case. Control boards are often misdiagnosed—make sure you check more commonly defective parts before replacing the main control board.
Electrolux Dishwasher won’t latch
01 – Electrolux Dishwasher Door Hinge
If the door hinges are damaged, the door won’t be able to latch properly. Inspect the door hinges for damage. If a hinge is bent or broken, replace it.
02 – Electrolux Dishwasher Door Seal
A dishwasher door having trouble latching could be caused by a damaged or misaligned door seak. Confirm the seal is fully seated in its track and replace if necessary.
03 – Electrolux Dishwasher Door Spring
A dishwasher door spring is attached to a cable to prevent the door from dropping down when opened and to allow the door to be more easily closed and latched. If the door feels heavy when opened or falls quickly, a broken door spring or cable is likely the cause. If the damaged component is not replaced, the strain on the door hinge can lead to hinge failure which can result in the door not latching properly. It is recommended to replace both door springs at the same time to reduce uneven wear.
04 – Electrolux Dishwasher Door Latch
Inspect the door latch assembly for damage. If the door latch is broken, replace it. The door latch is not repairable—if it is broken, you must replace it.
05 – Electrolux Dishwasher Door Cable
A dishwasher door cable is attached to a spring to prevent the door from dropping down when opened and to allow the door to be more easily closed and latched. If the door feels heavy when opened or falls quickly, a broken door cable or spring is likely the cause. If the damaged component is not replaced, the strain on the door hinge can lead to hinge failure which can result in the door not latching properly. It is recommended to replace both door cables at the same time to reduce uneven wear.
06 – Electrolux Dishwasher Door Strike
Inspect the door strike assembly for damage. If the door strike is broken, replace it. The door strike is not repairable—if it is broken, you must replace it.
07 – Electrolux Dishwasher Door Gasket
A dishwasher door having trouble latching could be caused by a damaged or misaligned door gasket. Confirm the gasket is fully seated in its track and replace if necessary.
Electrolux Dishwasher won’t start
Electrolux Dishwasher Thermal Fuse
The thermal fuse shuts off power to the dishwasher if it overheats. If the thermal fuse blows, it will prevent the dishwasher from starting. To determine if the thermal fuse is defective, use a multimeter to test the fuse for continuity. If the thermal fuse does not have continuity, replace it.
Electrolux Dishwasher Door Switch
The door switch prevents the dishwasher from running while the door is open. If the door switch is defective, the switch will prevent the dishwasher from running even when the door is closed. To determine if the door switch is at fault, use a multimeter to test the switch for continuity. If the switch does not have continuity, replace it.
Electrolux Dishwasher Wire Harness
If the dishwasher start button appears to work, but the dishwasher still won’t start, a wire harness which sends power from the control board to the pump components could be damaged. Inspect the wire harness for any frayed or broken wires and replace if necessary.
Electrolux Dishwasher Door Latch
The door latch ensures that the dishwasher door latches shut. If the door does not latch properly, the door switch might prevent the dishwasher from running. If the door latch is broken, replace it.
Electrolux Dishwasher Main Control Board
The main control board provides power to nearly every component of the dishwasher. If there is a problem with the main control board, it might not send voltage to the dishwasher, causing the dishwasher not to start. Control boards are often misdiagnosed—make sure you check more commonly defective parts before replacing the main control board.
Electrolux Dishwasher Drain Pump
A dishwasher drain pump assists in removing the water from the tank at various times during operation. Since the unit will drain some water from the tank prior to the fill cycle beginning, a faulty drain pump unable to drain any water could prevent the dishwasher from starting.
Electrolux Dishwasher Touchpad and Control Panel
To determine if the touchpad is at fault, try pressing various buttons on the touchpad. If some of the buttons don’t respond, the touchpad might be defective. (Some manufacturers sell the touchpad separately from the control panel. Other manufacturers require that you purchase the touchpad and control panel together. If you cannot replace the touchpad individually, replace the touchpad and control panel.)
Electrolux Dishwasher Touchpad
To determine if the touchpad is at fault, try pressing various buttons on the touchpad. If some of the buttons don’t respond, the touchpad might be defective. If the touchpad isn’t working properly, replace it. (Some manufacturers sell the touchpad separately from the control panel. Other manufacturers require that you purchase the touchpad and control panel together. If you cannot replace the touchpad individually, replace the touchpad and control panel.)
Incoming Power Problem
If there are no indicator lights or any noise from the dishwasher when it is turned on, it is likely that power is not reaching the dishwasher. Check the circuit breakers and GFCI (ground-fault circuit interrupter) outlets, if applicable, to confirm they have not tripped, or inspect any fuses to confirm none have blown. Since most dishwashers are hardwired (not plugged in) the junction box on the dishwasher should be checked for loose or burnt wires.
Electrolux Dishwasher Pump and Motor Assembly
A defective dishwasher pump and motor assembly may prevent the appliance from starting. Make sure that power is getting to the circulation pump and motor. If power is getting to the pump and motor assembly but it still won’t run, replace the pump and motor assembly.
Electrolux Dishwasher Control Board
A dishwasher’s control board provides power to nearly every electrical component in the dishwasher. A faulty board may be unable to supply power to the electrical components or respond to the touchpad buttons being pressed, which can prevent dishwasher from starting.
Electrolux Dishwasher Timer
The timer allows power to flow to the proper parts at the proper times. If the timer isn’t working properly, it might not send voltage to the dishwasher, causing it not to start. Timers are often misdiagnosed—make sure you check more commonly defective parts before replacing the timer.
Electrolux Dishwasher Circulation Pump
A defective dishwasher circulation pump may prevent the appliance from starting. Make sure that power is getting to the circulation pump and motor. If power is getting to the circulation pump but it still won’t run, replace the component.
Electrolux Dishwasher User Control and Display Board
A dishwasher’s user control and display board allows the user to select a wash and drying cycle and start the appliance. If the start button won’t work, it’s likely the user control and display board is malfunctioning and will need to be replaced with a new one.
Electrolux Dishwasher leaking from motor area
Electrolux Dishwasher Shaft Seal
First, try to determine the source of the leak. If the water is leaking from the motor shaft area, the motor shaft seal is likely defective. If the seal is defective, replace it. (Some manufacturers sell the seal independently of the impeller. Other manufacturers require that you purchase the impeller and seal together. Still other manufacturers require that you purchase the entire pump and motor assembly instead of the impeller and seal. It is more cost effective to replace the seal kit rather than the impeller and seal.)
Electrolux Dishwasher Impeller and Seal Kit
First, try to determine the source of the leak. If the water is leaking from the motor shaft area, the motor shaft seal is likely defective. If the seal is defective, replace it. (Some manufacturers sell the seal independently of the impeller. Other manufacturers require that you purchase the impeller and seal together. Still other manufacturers require that you purchase the entire pump and motor assembly instead of the impeller and seal. It is usually more cost effective to replace the impeller and seal kit rather than the pump and motor assembly.)
Electrolux Dishwasher Seal Kit
First, try to determine the source of the leak. If the water is leaking from the motor shaft area, the motor shaft seal is likely defective. If the seal is defective, replace it. (Some manufacturers sell the seal independently of the impeller. Other manufacturers require that you purchase the impeller and seal together. Still other manufacturers require that you purchase the entire pump and motor assembly instead of the impeller and seal. It is more cost effective to replace the seal kit rather than the impeller and seal.)
Electrolux Dishwasher Pump and Motor Assembly
If the dishwasher is leaking water from the motor area, the entire pump and motor assembly need to be replaced. First, try to determine the source of the leak. If the water is leaking from the drain pump, the impeller and seal is likely the cause. On most dishwashers, you can replace the impeller and seal kit independently of the drain pump. However, if you do not want to disassemble the pump, or if the impeller and seal kit is not available separately, you can replace the entire pump and motor assembly. In addition, if the motor shaft is rusted and the new impeller won’t fit onto the shaft, replace the pump and motor assembly.
Electrolux Dishwasher Water Inlet Valve
A dishwasher’s water inlet valve opens following a short drain cycle to fill the tank with water in preparation for the wash cycle. If the inlet valve is cracked or damaged, the dishwasher can leak water near the motor area beneath the dishwasher tank.
Electrolux Dishwasher Drain Hose
A dishwasher leak near the motor area could be caused by damaged drain hose. Confirm the hose is secured to the drain pump outlet port and check for any cracks or holes in the hose itself. Replace a damaged drain hose with a new one.
Electrolux Dishwasher Sump
Most dishwasher pumps have a large bowl, or sump, which collects the water that enters the pump. The sump is lined with a rubber seal that prevents water from entering the dishwasher tub. If the sump seal is worn out, the sump will leak water. If the sump seal is leaking water, replace it. In addition, on some dishwashers, a lock ring secures the sump to the bottom of the tub. If the lock ring is cracked or damaged, replace it.
Electrolux Dishwasher Drain Pump
A dishwasher drain pump assists in removing the water from the tank during the drain cycles by using an impeller to force or push the water through a drain hose to the garbage disposal or a sink drain pipe. If the drain pump is cracked or damaged, the dishwasher can leak water near the motor area beneath the dishwasher tank.
Electrolux Dishwasher Circulation Pump
A dishwasher circulation pump circulates the water through the spray arms to wash the dishware. If the pump is cracked or damaged, or a seal is worn out, the dishwasher can leak water near the motor area beneath the dishwasher tank.
Electrolux Dishwasher Diverter Motor
A dishwasher’s diverter motor operates a diverter disc to redirect the water between the upper and lower wash arms. If the stem seal is damaged, it can potentially leak water behind the lower access panel near the pump motor area. If water is leaking from the diverter motor area, the diverter motor will need to be changed.
Electrolux Dishwasher leaking
Electrolux Dishwasher Water Inlet Valve
The water inlet valve opens to allow water to enter the dishwasher. If the water inlet valve is stuck open, the dishwasher will continue to fill with water until the dishwasher leaks or overflows. If the water inlet valve is at fault, replace it. Water inlet valves are not repairable—if the valve is defective, you must replace it.
Electrolux Dishwasher Center Wash Arm Assembly
If the wash arm is cracked, it can allow a jet of water to spray toward the door seal, causing a leak. Remove the wash arm and inspect it for cracks. If the wash arm is cracked, replace it. Do not attempt to seal the crack with glue—the glue will break down in the dishwasher. If the wash arm is intact, make sure the screws in the wash arm support are tight. If the wash arm support is loose, water can spray out between the wash arm support and the lower pump housing, causing waves. These waves can cause water to leak out of the bottom of the door.
Electrolux Dishwasher Lower Wash Arm Assembly
If the wash arm is cracked, it can force water to spray directly toward the lower part of the dishwasher door. The water can then be forced under the door and onto the floor, causing a leak. Remove the wash arm and inspect it for cracks. If the wash arm is cracked, replace it. Do not attempt to seal the crack with glue—the glue will break down in the dishwasher. If the wash arm is intact, make sure the screws in the wash arm support are tight. If the wash arm support is loose, water can spray out between the wash arm support and the lower pump housing, causing waves. These waves can cause water to leak out of the bottom of the door.
Electrolux Dishwasher Upper Wash Arm Assembly
If the upper wash arm is cracked, it can force water to spray directly toward the dishwasher door seal, causing a leak. Remove the wash arm and inspect it for cracks. If the wash arm is cracked, replace it. Do not attempt to seal the crack with glue—the glue will break down in the dishwasher. If the wash arm is intact, make sure the screws in the wash arm support are tight. If the wash arm support is loose, water can spray out between the wash arm support and the lower pump housing, causing waves. These waves can cause water to leak out of the bottom of the door.
Electrolux Dishwasher Door Seal
Look for tears, gaps or cuts in the seal that could cause a dishwasher door leak. To determine if the door seal is making good contact, try closing the dishwasher door on a dollar bill all the way around the door. If the dollar bill does not stick, there is a gap in the seal. If the door seal has any gaps or leaks, replace it. If the door seal is working properly but the dishwasher is still leaking, check the door hinges. If the hinges are bent, the door will not close properly, creating a gap between the door seal and the dishwasher. If the hinges are bent, replace them.
Electrolux Dishwasher Detergent Dispenser
A dishwasher detergent dispenser releases detergent into the tank during the wash cycle. Some dispensers with a rotating cover, or a latch, have an O-ring or seal that can wear out and allow water to leak inbetween the door panels and onto the floor near the bottom of the door.
Electrolux Dishwasher Door Gasket
Look for tears, gaps or cuts in the gasket that could cause a dishwasher door leak. To determine if the door gasket is making good contact, try closing the dishwasher door on a dollar bill all the way around the door. If the dollar bill does not stick, there is a gap in the gasket. If the door gasket has any gaps or leaks, replace it. If the door gasket is working properly but the dishwasher is still leaking, check the door hinges. If the hinges are bent, the door will not close properly, creating a gap between the door gasket and the dishwasher. If the hinges are bent, replace them.
Wrong type or incorrect amount of detergent
Make sure to use the proper dishwasher detergent. Use the proper amount of detergent for your water hardness; too much soap in soft water can cause oversudsing and leaking.
Electrolux Dishwasher Drain Pump
A dishwasher drain pump assists in removing the water from the tank during the drain cycles by using an impeller to force or push the water through a drain hose to the garbage disposal or a sink drain pipe. If the drain pump is cracked or damaged, the dishwasher can leak water behind the lower panel beneath the dishwasher tank.
Electrolux Dishwasher Drain Hose
A dishwasher leak behind the lower access panel could be caused by damaged drain hose. Confirm the hose is secured to the drain pump outlet port and check for any cracks or holes in the hose itself. Replace a damaged drain hose with a new one.
Electrolux Dishwasher Sump
Most dishwashers have a large bowl, or sump, which collects the water that enters the pump. The sump is lined with a rubber seal that prevents water from leaking between the sump and the dishwasher tub. If the sump seal is worn out, the sump will leak water. If the sump seal is leaking water, replace it. In addition, on some dishwashers, a lock ring secures the sump to the bottom of the tub. If the lock ring is cracked or damaged, replace it.
Electrolux Dishwasher Circulation Pump
A dishwasher circulation pump circulates the water through the spray arms to wash the dishware. If the pump is cracked or damaged, or a seal is worn out, the dishwasher can leak water behind the lower access panel.
Electrolux Dishwasher Pump and Motor Assembly
A dishwasher pump and motor assembly circulates the water through the spray arms to wash the dishware. If the assembly is cracked or damaged, or a seal is worn out, the dishwasher can leak water behind the lower panel beneath the dishwasher tank.
Electrolux Dishwasher Diverter Motor
A dishwasher’s diverter motor operates a diverter disc to redirect the water to the upper spray arm or arms. If the motor itself is damaged, it can potentially leak water behind the lower access panel. Inspect the motor housing for any cracks and replace if necessary.
Electrolux Dishwasher lights flashing or blinking
Electrolux Dishwasher Heating Element
The heating element heats up the water to operating temperature. If the water doesn’t reach the proper temperature after a set amount of time, a light on the control panel might start flashing. To determine if the heating element has burned out, use a multimeter to test it for continuity. If the heating element does not have continuity, replace it.
Electrolux Dishwasher Heating Element Assembly
The heating element assembly heats up the water to operating temperature. If the water doesn’t reach the correct temperature after a set amount of time, a light on the control panel might start flashing. To determine if the heating element assembly has burned out, use a multimeter to test the heating element for continuity.
Electrolux Dishwasher Water Inlet Valve
If the dishwasher lights are flashing or blinking, the cause could be a faulty water inlet valve. You can use a multimeter to test the valve’s solenoids for electrical continuity to help determine if the component is functioning properly or not.
Electrolux Dishwasher Door Latch
A dishwasher’s lights flashing or blinking could indicate a problem with a micro switch inside the door latch assembly. To determine if the micro switch is at fault, use a multimeter to test the switch for continuity. If the switch does not have continuity, replace it or the entire latch assembly.
Electrolux Dishwasher Control Board
The control board provides power to nearly every component of the dishwasher. It’s possible that the board has shorted and is causing the lights to flash or blink unexpectedly. Check the owner’s manual for possible fault codes as one of the components may have failed. If the control board is not sending power to one of the components, it’s likely the control board is at fault and will need to be replaced.
Electrolux Dishwasher Main Control Board
The main control board provides power to nearly every component of the dishwasher. It’s possible that the board has shorted and is causing the lights to flash or blink. Check the owner’s manual for possible fault codes as one of the components may have failed. If the control board is not sending power to one of the components, it’s likely the main control board is at fault and will need to be replaced.
Check Fault Codes
If the dishwasher lights are flashing or blinking or there is a fault code in the display window, consult the wiring diagram, tech sheet, and/or user manual to find out more information about the error.
Electrolux Dishwasher User Control and Display Board
The user control and display board is the component that allows the user to choose a dishwasher’s wash and dry setting. If the control and display board is defective, it could be causing the lights to flash or blink unexpectedly. If the control panel buttons were working intermittently prior to the lights flashing, it’s likely the user control and display board is at fault and will need to be replaced.
Electrolux Dishwasher Drain Pump
The drain pump uses an impeller to force water through the drain hose. If the drain pump is not working, a light on the control panel might start flashing. To determine if the drain pump is defective, check the pump motor for continuity using a multimeter. If the motor does not have continuity, replace the drain pump. Drain pumps are not repairable—if the drain pump is defective, you must replace it.
Electrolux Dishwasher Touchpad and Control Panel
First, confirm that the display is working. If the display is working, try pressing the touchpad buttons. If some of the buttons don’t respond correctly, it is possible that the entire touchpad and control panel is at fault. (Some manufacturers sell the touchpad separately from the control panel. Other manufacturers require that you purchase the touchpad and control panel together. If you cannot replace the touchpad individually, replace the touchpad and control panel.)
Electrolux Dishwasher Touchpad
First, confirm that the display is working. If the display is still working, try pressing some of the touchpad buttons. If some of the buttons respond correctly but others don’t, it is likely that the touchpad is at fault. (Some manufacturers sell the touchpad separately from the control panel. Other manufacturers require that you purchase the touchpad and control panel together. If you cannot replace the touchpad individually, replace the touchpad and control panel.)
Electrolux Dishwasher Control Panel
If the dishwasher lights are flashing or blinking, first confirm that the display is working. If the display is working, try pressing the control panel buttons. If some of the buttons don’t respond correctly, it is possible that the entire control panel is at fault and the component will need to be replaced.
Electrolux Dishwasher buttons not working
Electrolux Dishwasher Touchpad and Control Panel
First, ensure that the display works. If the dishwasher display is working but the some of the button don’t respond correctly, the touchpad and control panel might need to be replaced. (Some manufacturers sell the touchpad separately from the control panel. Other manufacturers require that you purchase the touchpad and control panel together. If you cannot replace the touchpad individually, replace the touchpad and control panel.)
Electrolux Dishwasher Touchpad
First, confirm that the dishwasher display is working. If the display is still working, try pressing some of the touchpad buttons. If some of the buttons respond correctly but others don’t, it is likely that the touchpad is at fault. (Some manufacturers sell the touchpad separately from the control panel. Other manufacturers require that you purchase the touchpad and control panel together. If you cannot replace the touchpad individually, replace the touchpad and control panel.)
Incoming Power Problem
If there are no indicator lights or any noise from the dishwasher when it is turned on, it is likely that power is not reaching the dishwasher. Check the circuit breakers and GFCI (ground-fault circuit interrupter) outlets, if applicable, to confirm they have not tripped, or inspect any fuses to confirm none have blown. Since most dishwashers are hardwired (not plugged in) the junction box on the dishwasher should be checked for loose or burnt wires.
Dishwasher in lock mode
Many dishwashers have a child lock or “Sabbath” feature which will prevent the buttons from being used when the feature is engaged. The dishwasher could also be in “Demo” mode or another mode which prevents full operation. Consult the dishwasher’s user manual for information regarding locking/unlocking the control panel.
Electrolux Dishwasher Door Latch
If the dishwasher buttons aren’t working, it’s possible the door latch is malfunctioning and preventing a wash cycle from being started. Inspect the door latch for any damage. you can also use a multimeter to test the micro switch inside the door latch for electrical continuity. If the switch does not have continuity, the switch or latch assembly should be replaced.
Electrolux Dishwasher Main Control Board
The main control board regulates nearly every function in the dishwasher. If there is a problem with the main control board, it might not send voltage to the dishwasher touchpad, causing the touchpad buttons not to work. Control boards are often misdiagnosed; make sure you test more commonly defective parts before replacing the main control board.
Electrolux Dishwasher Control Board
The control board regulates nearly every function in the dishwasher. If there is a problem with the control board, it might not send voltage to the dishwasher touchpad, causing the touchpad buttons not to work. Control boards are often misdiagnosed; make sure you test more commonly defective parts before replacing the control board.
Check Fault Codes
If the dishwasher lights are flashing or blinking or there is a fault code in the display window, consult the wiring diagram, tech sheet, and/or user manual to find out more information about the error.
Electrolux Dishwasher User Control and Display Board
The user control and display board is the component that allows the user to choose a dishwasher’s wash and dry setting. If some or all of the buttons aren’t working, you should first determine if the control works at all or if the display indicator lights are illuminated. If lights are illuminated or some of the control works, it’s likely the user control and display board is faulty and will need to be replaced. If no lights and no functionality is present, it’s more likely a door switch or main control board is at fault.
Electrolux Dishwasher Control Panel
The control panel is the component that allows the user to choose a dishwasher’s wash and dry setting. If some or all of the buttons aren’t working, you should first determine if the control works at all or if the display indicator lights are illuminated. If lights are illuminated or some of the control works, it’s likely the control panel is faulty and will need to be replaced. If no lights and no functionality is present, it’s more likely a line fuse or main control board is at fault.
Electrolux Dishwasher Door Switch
If the dishwasher buttons aren’t working, it’s possible a door switch is malfunctioning and preventing a wash cycle from being started. To determine if the door switch is at fault, use a multimeter to test the switch for continuity. If the switch does not have continuity, replace it.
Electrolux Dishwasher Micro Switch
If the dishwasher buttons aren’t working, it’s possible a micro switch in the door latch is malfunctioning and preventing a wash cycle from being started. To determine if the micro switch is at fault, use a multimeter to test the switch for continuity. If the switch does not have continuity, replace it.
Electrolux Dishwasher Dishwasher not draining
Clogged Sump Filters
There is usually a course and fine filter. If they are clogged, you will get low water flow and poor washability. To clean filters, remove them and wash with soap, warm water, and brush. If the filters cannot be cleaned effectively or if they are damaged, they will need to be replaced.
Electrolux Dishwasher Drain Pump
The drain pump uses an impeller to force water through the drain hose. If the drain pump motor is not working, the dishwasher won’t drain. To determine if the drain pump is defective, check the pump motor for continuity using a multimeter. If the motor does not have continuity, or if is getting power but won’t run, replace the drain pump. Drain pumps are not repairable—if the drain pump is defective, you must replace it.
Electrolux Dishwasher Control Board
A dishwasher’s control board provides power to nearly every electrical component in the dishwasher. A faulty board may be unable to supply power to the drain pump, preventing it from drawing the water out of the tank and forcing it through the drain hose to the garbage disposal or sink drain pipe.
Electrolux Dishwasher Drain Impeller
The drain impeller pushes water through the drain hose and into the garbage disposer or drain line. If the impeller is broken, replace it.
Electrolux Dishwasher Drain Solenoid Kit
The drain solenoid opens the drain valve to allow the water to exit the dishwasher. If the drain solenoid fails the valve will not open causing the dishwasher not to drain.
Electrolux Dishwasher Drain Valve
Over time, the drain valve can get clogged with debris. To ensure that water can flow through the drain valve, clean out the valve. If the drain valve is clear of debris but it still won’t actuate, replace it. Drain valves are not repairable—if the drain valve is defective, you must replace it.
Electrolux Dishwasher Main Control Board
A dishwasher’s main control board provides power to nearly every electrical component in the dishwasher. A faulty board may be unable to supply power to the drain pump, preventing it from drawing the water out of the tank and forcing it through the drain hose to the garbage disposal or sink drain pipe.
Electrolux Dishwasher Pump and Motor Assembly
The motor drives an impeller to force water out of the drain hose. If the motor runs during the drain cycle, check for a blockage in the drain line. If the motor won’t run during the drain cycle or if it just hums when it should be running, the pump and motor assembly might need to be replaced.
Clogged or Improperly Installed Garbage Disposer
If the garbage disposer was installed recently, the drain plug may not have been removed. All garbage disposers are sold with a solid plug in the drain tube. If the dishwasher is not connected to the garbage disposer, the plug must remain in the drain tube. However, if the dishwasher is connected to the garbage disposer, the plug must be removed. If the garbage disposer wasn’t replaced recently, it is possible that the disposer is clogged. Remove the dishwasher drain hose from the disposer and clean out both the fitting on the disposer and the end of the drain hose. These are the most common places to find an obstruction if the dishwasher won’t drain.
Electrolux Dishwasher Drain Hose
The drain hose might be clogged. To unclog the drain hose, remove the drain hose from both the dishwasher and the sink drain and clean it out. The drain hose is most commonly clogged near the garbage disposer or dishwasher drain branch tailpiece.
Electrolux Dishwasher Check Valve
The check valve prevents water from returning to the dishwasher after it has drained. If the valve gets stuck closed, it will prevent the water from draining. If the check valve is stuck closed, try cleaning it out and then replace it if necessary.
Electrolux Dishwasher Filter Assembly
A dishwasher’s filter assembly usually consists of both a course and a fine filter located in the sump. If one or both of these filters is clogged, the appliance will probably not drain properly. If the filters cannot be cleaned effectively or if they are damaged, they will need to be replaced.
Electrolux Dishwasher Screen Filter
A dishwasher will usually have both a course and a fine screen filter located in the sump. If one or both of these filters is clogged, the appliance will probably not drain properly. If the filters cannot be cleaned effectively or if they are damaged, they will need to be replaced.
Electrolux Dishwasher Strainer
Dishwashers will use a strainer located in the sump to catch food particles. If the strainer is clogged, the appliance will probably not drain properly. If the stainer cannot be cleaned effectively or is damaged, it will need to be replaced.
