Call (323) 792-1970
Customer service:    323-792-1970

Dacor Refrigerator Error Code E4

Dacor Refrigerator Error Codes

Dacor Refrigerator Error Code E4

If you see the error code E4 on your Dacor refrigerator, it means that the defrost timer has failed. The defrost timer is responsible for controlling the defrost cycle, which helps to prevent frost from building up on the evaporator coils.

To troubleshoot this error code, you can try the following steps:

  1. Check the power supply to the defrost timer. Make sure that the timer is plugged in and that the power is turned on.
  2. Check the connections between the defrost timer and the other components of the defrost system. Make sure that all of the connections are secure.
  3. Replace the defrost timer. If you have checked the power supply and the connections and the error code is still appearing, then you will need to replace the defrost timer.

To replace the defrost timer, you will need to follow these steps:

  1. Unplug the refrigerator from the power outlet.
  2. Remove the back panel of the refrigerator.
  3. Locate the defrost timer. It is typically located near the evaporator coils.
  4. Disconnect the wires from the defrost timer.
  5. Remove the defrost timer from the refrigerator.
  6. Install the new defrost timer.
  7. Reconnect the wires to the new defrost timer.
  8. Replace the back panel of the refrigerator.
  9. Plug the refrigerator back in.

Once you have replaced the defrost timer, the error code should be cleared. If the error code does not clear, then you may need to contact a qualified technician for further diagnosis and repair.

Additional Troubleshooting Tips

  • If you are not comfortable replacing the defrost timer yourself, you can contact a qualified technician for assistance.
  • If you are replacing the defrost timer, make sure to purchase a replacement timer that is compatible with your refrigerator model.
  • When replacing the defrost timer, be careful not to damage any of the other components of the defrost system.

The defrost timer is a relatively inexpensive part, so replacing it is typically a cost-effective solution to the error code E4.

Continue reading

Dacor Refrigerator Error Code E2

Dacor Refrigerator Error Codes

Dacor Refrigerator Error Code E2

If you see the error code E2 on your Dacor refrigerator, it means that the freezer temperature sensor has failed. The freezer temperature sensor is responsible for sending the temperature reading to the refrigerator’s control board. If the sensor fails, the control board will not be able to accurately determine the temperature of the freezer.

This can lead to a number of problems, including:

  • The freezer may not cool down properly.
  • The ice maker may not work properly.
  • The refrigerator may not be energy efficient.

Here are some steps you can take to troubleshoot the error code E2:

  1. Check the freezer temperature sensor for proper placement. The freezer temperature sensor is typically located in the freezer compartment, near the back. Make sure that the sensor is properly seated in its socket.
  2. Check the freezer temperature sensor for functionality. You can do this by using a multimeter to measure the resistance of the sensor. The resistance should be between 10,000 and 100,000 ohms. If the resistance is outside of this range, the sensor is faulty and needs to be replaced.

If you have checked the freezer temperature sensor for proper placement and functionality and the error code is still present, you will need to contact a qualified technician for further diagnosis and repair.

Self-repair

If you are comfortable working with electrical components, you can replace the freezer temperature sensor yourself. To do this, you will need to purchase a new sensor from a Dacor authorized dealer.

Once you have the new sensor, follow these steps to replace it:

  1. Unplug the refrigerator from the power outlet.
  2. Remove the back panel of the freezer compartment.
  3. Locate the freezer temperature sensor.
  4. Remove the old sensor from its socket.
  5. Insert the new sensor into the socket.
  6. Reinstall the back panel of the freezer compartment.
  7. Plug the refrigerator back into the power outlet.

After you have replaced the freezer temperature sensor, the error code should be cleared. If the error code is still present, contact a qualified technician for further diagnosis and repair.

Continue reading

Dacor Refrigerator Error Code F19

Dacor Refrigerator Error Codes

Dacor Refrigerator Error Code F19

The F19 error code on a Dacor refrigerator indicates a failure in the water valve solenoid. The water valve solenoid is responsible for opening and closing the water valve to supply water to the ice maker.

The most likely solution to the F19 error code is to replace the water valve solenoid. The water valve solenoid is a relatively inexpensive and easy-to-replace part.

Troubleshooting Steps:

Before replacing the water valve solenoid, you should perform a few troubleshooting steps to verify that the solenoid is the actual cause of the error code.

  1. Check the water supply to the refrigerator. Make sure that the water supply is turned on and that the water pressure is adequate.
  2. Check the ice maker door. Make sure that the door is closed properly.
  3. Check the ice maker bin. Make sure that the bin is not full.

If you have checked all of these things and you are still seeing the F19 error code, then it is likely that the water valve solenoid is faulty.

To replace the water valve solenoid:

  1. Unplug the refrigerator from the power outlet.
  2. Remove the screws that secure the ice maker to the refrigerator.
  3. Remove the ice maker from the refrigerator.
  4. Locate the water valve solenoid. It is usually located near the bottom of the ice maker.
  5. Disconnect the wires from the water valve solenoid.
  6. Remove the screws that secure the water valve solenoid to the refrigerator.
  7. Install the new water valve solenoid.
  8. Connect the wires to the new water valve solenoid.
  9. Reinstall the ice maker to the refrigerator.
  10. Plug the refrigerator back into the power outlet.

Once you have replaced the water valve solenoid, the F19 error code should be cleared. If the error code persists, then you may need to contact a qualified technician for further diagnosis and repair.

Additional Information:

The water valve solenoid is a relatively small, cylindrical component that is typically made of plastic. It has two wires that connect it to the refrigerator’s control board. The solenoid is activated by a signal from the control board. When the solenoid is activated, it opens the water valve, allowing water to flow to the ice maker.

The water valve solenoid can fail for a variety of reasons, including:

  • Electrical overload
  • Mechanical failure
  • Corrosion

If you are not comfortable replacing the water valve solenoid yourself, you can contact a qualified technician for assistance.

Continue reading

Dacor Refrigerator Error Code F18

Dacor Refrigerator Error Codes

Dacor Refrigerator Error Code F18

The Dacor refrigerator error code F18 indicates that the door switch has failed. The door switch is a safety device that prevents the refrigerator from operating if the door is open. When the door is closed, the door switch closes and completes an electrical circuit. This circuit tells the refrigerator that the door is closed and that it can operate normally.

If the door switch fails, the refrigerator will not operate and the error code F18 will be displayed.

If you see the error code F18, you can try to troubleshoot the problem yourself. Here are some steps you can take:

  1. Check the door seal. Make sure that the door seal is properly aligned and that it is sealing tightly around the door.
  2. Check the door switch. Use a multimeter to test the door switch for continuity. If the door switch does not have continuity, it will need to be replaced.

Replacement Instructions

To replace the door switch, you will need to follow the instructions in your refrigerator’s owner’s manual. Here are some general steps you can follow:

  1. Unplug the refrigerator from the power outlet.
  2. Remove the screws that secure the door switch to the refrigerator.
  3. Remove the old door switch.
  4. Install the new door switch.
  5. Secure the new door switch with screws.
  6. Plug the refrigerator back into the power outlet.

Additional Troubleshooting Tips

  • If you have replaced the door switch and the error code F18 is still displayed, there may be another underlying problem with the refrigerator. In this case, you should contact a qualified appliance repair technician for further diagnosis and repair.
  • If you are not sure how to troubleshoot or repair the door switch, you should contact a qualified appliance repair technician.

Continue reading

Dacor Refrigerator Error Code F17

Dacor Refrigerator Error Codes

Dacor Refrigerator Error Code F17

The F17 error code indicates that a temperature sensor in your Dacor refrigerator has failed.

This can cause the refrigerator to malfunction in a number of ways, including:

  • The refrigerator may not be able to maintain the correct temperature.
  • The refrigerator may turn on and off frequently.
  • The refrigerator may not be able to defrost properly.

To troubleshoot the F17 error code, you can follow these steps:

  1. Check the power supply to the refrigerator. Make sure that the power cord is plugged in and that the outlet is working.
  2. Check the temperature sensor connections. Make sure that the connections are secure and that the wires are not damaged.
  3. Replace the temperature sensor. If you have checked the power supply and the connections and the error code is still occurring, you will need to replace the temperature sensor.

Replacing the temperature sensor:

  1. Turn off the power to the refrigerator.
  2. Remove the back panel of the refrigerator.
  3. Locate the temperature sensor. It is typically a small, black, cylindrical device.
  4. Disconnect the wires from the temperature sensor.
  5. Install the new temperature sensor.
  6. Reconnect the wires to the temperature sensor.
  7. Replace the back panel of the refrigerator.
  8. Turn on the power to the refrigerator.

If you are not comfortable replacing the temperature sensor yourself, you can contact a qualified technician for assistance.

Here are some additional tips for troubleshooting the F17 error code:

  • If you are replacing the temperature sensor, make sure to purchase the correct replacement part for your refrigerator model.
  • If you are not sure how to replace the temperature sensor, you can consult your refrigerator owner’s manual or watch a video online.
  • If you have replaced the temperature sensor and the error code is still occurring, you may need to contact a qualified technician for further diagnosis.

Continue reading

Dacor Refrigerator Error Code F16

Dacor Refrigerator Error Codes

Dacor Refrigerator Error Code F16

The Dacor refrigerator error code F16 indicates a door alarm. This means that the door seal is not properly aligned or is damaged. This can cause the refrigerator to lose cold air, which can lead to food spoilage.

To troubleshoot the error code F16, follow these steps:

  1. Check the door seal for proper alignment. The door seal should be snug against the doorframe, with no gaps or tears. If the seal is not properly aligned, you can try to adjust it by hand. If you are unable to adjust the seal, you may need to replace it.
  2. Check the door switch for proper operation. The door switch is a small switch that is located on the doorframe. It tells the refrigerator when the door is open or closed. If the door switch is not working properly, it can cause the error code F16 to be displayed. To check the door switch, you can use a multimeter to test its continuity. If the door switch is not working properly, you will need to replace it.

DIY Repair

If you are able to determine that the door seal is properly aligned and the door switch is working properly, you may be able to fix the error code F16 yourself. To do this, you will need to replace the door seal.

To replace the door seal, follow these steps:

  1. Unplug the refrigerator.
  2. Remove the screws that hold the door in place.
  3. Carefully remove the door from the refrigerator.
  4. Remove the old door seal.
  5. Install the new door seal.
  6. Reinstall the door on the refrigerator.
  7. Plug the refrigerator back in.

If you are unable to troubleshoot the error code F16 yourself, or if you are not comfortable replacing the door seal, you should contact a qualified technician for assistance.

Continue reading

Dacor Refrigerator Error Code F15

Dacor Refrigerator Error Codes

Dacor Refrigerator Error Code F15

The F15 error code on a Dacor refrigerator indicates a failure of the condenser fan. The condenser fan is responsible for circulating air over the condenser coils, which helps to remove heat from the refrigerant. When the condenser fan fails, the refrigerator will not be able to cool properly.

Troubleshooting:

  1. Check the condenser fan motor. The condenser fan motor is a small electric motor that drives the fan blades. To check the motor, disconnect the power to the refrigerator and then unplug the fan motor. Use a multimeter to measure the resistance between the terminals of the motor. The resistance should be within the specifications listed in the refrigerator’s service manual. If the resistance is out of specification, replace the motor.
  2. Check the condenser fan blades. The condenser fan blades should be free of debris and should not be bent or damaged. If the blades are damaged, replace them.
  3. Check the condenser fan wiring. The condenser fan wiring should be free of damage and should be properly connected. If the wiring is damaged, repair or replace it.

If you are comfortable working with electrical components, you can replace the condenser fan motor yourself:

  1. Disconnect the power to the refrigerator.
  2. Unplug the fan motor.
  3. Remove the screws that secure the fan motor to the condenser coils.
  4. Remove the old fan motor.
  5. Install the new fan motor.
  6. Secure the new fan motor with the screws.
  7. Plug in the fan motor.
  8. Restore power to the refrigerator.

Additional Information:

  • The F15 error code may also be displayed if the condenser fan is not receiving power. To check the power supply to the fan, disconnect the power to the refrigerator and then use a multimeter to measure the voltage at the fan terminals. The voltage should be within the specifications listed in the refrigerator’s service manual. If the voltage is not within specification, repair or replace the power supply.
  • The F15 error code may also be displayed if the condenser coils are dirty or clogged. To clean the condenser coils, unplug the refrigerator and then use a vacuum cleaner to remove any debris from the coils. You can also use a soft brush to clean the coils.

Continue reading

Dacor Refrigerator Error Code F14

Dacor Refrigerator Error Codes

Dacor Refrigerator Error Code F14

The error code F14 indicates that the freezer fan in your Dacor refrigerator has failed. This can cause the freezer temperature to rise, which can lead to food spoilage.

To troubleshoot this error code, you can follow these steps:

  1. Check the power supply to the freezer fan. Make sure that the power cord is plugged in and that the circuit breaker is not tripped.
  2. Check the connections to the freezer fan. Make sure that the wiring is secure and that there are no broken or frayed wires.
  3. Check the freezer fan itself. Make sure that the fan is spinning freely and that there are no obstructions.

If you have checked all of these things and the error code is still appearing, you will need to replace the freezer fan.

To replace the freezer fan, you will need the following tools:

  • Phillips head screwdriver
  • Torx screwdriver (may be required)

Instructions:

  1. Unplug the refrigerator from the power outlet.
  2. Remove the screws that secure the freezer cover.
  3. Lift off the freezer cover.
  4. Locate the freezer fan.
  5. Disconnect the wiring from the freezer fan.
  6. Remove the screws that secure the freezer fan.
  7. Lift out the old freezer fan.
  8. Install the new freezer fan.
  9. Connect the wiring to the new freezer fan.
  10. Secure the freezer fan with the screws.
  11. Replace the freezer cover.
  12. Plug the refrigerator back into the power outlet.

Once you have replaced the freezer fan, you should reset the error code. To do this, press and hold the “Freezer” button for 10 seconds. The error code should clear from the display.

If the error code does not clear, you may need to contact a qualified technician for further assistance.

Continue reading

Dacor Refrigerator Error Code F13

Dacor Refrigerator Error Codes

Dacor Refrigerator Error Code F13

The Dacor refrigerator error code F13 indicates that the ice maker control board has failed. The ice maker control board is responsible for controlling the operation of the ice maker, including the water supply, ice production, and ice storage.

There are several possible causes of the Dacor refrigerator error code F13, including:

  • A faulty ice maker control board
  • A loose or damaged connection between the ice maker control board and other components
  • A power surge or other electrical problem

If you see the Dacor refrigerator error code F13, you can try to troubleshoot the problem yourself by following these steps:

  1. Check the connections between the ice maker control board and other components. Make sure that all connections are secure and that there are no signs of damage.
  2. Check the power supply to the refrigerator. Make sure that the power is turned on and that the voltage is correct.
  3. If you have checked the connections and power supply and the error code is still present, you may need to replace the ice maker control board.

Replacing the Ice Maker Control Board:

To replace the ice maker control board, you will need to follow the instructions in your Dacor refrigerator owner’s manual. The following are general steps for replacing the ice maker control board:

  1. Disconnect the power to the refrigerator.
  2. Remove the screws that secure the ice maker control board to the refrigerator.
  3. Carefully remove the ice maker control board.
  4. Install the new ice maker control board.
  5. Secure the ice maker control board with screws.
  6. Reconnect the power to the refrigerator.

If you are not comfortable replacing the ice maker control board yourself, you should contact a qualified technician for assistance.

The Dacor refrigerator error code F13 may also be accompanied by other symptoms, such as:

  • The ice maker is not producing ice.
  • The ice maker is making ice that is cloudy or discolored.
  • The ice maker is making ice that is smaller than normal.

If you are experiencing any of these symptoms, it is likely that the ice maker control board is faulty.

Continue reading

Dacor Refrigerator Error Code F12

Dacor Refrigerator Error Codes

Dacor Refrigerator Error Code F12

If you see error code F12 on your Dacor refrigerator, it means that the ice maker motor has failed. The ice maker motor is responsible for turning the ice maker tray and dropping the ice cubes into the ice bin. If the ice maker motor is not working properly, the ice maker will not be able to make ice.

To troubleshoot error code F12, you can try the following steps:

  1. Check the power supply to the ice maker. Make sure that the ice maker is plugged in and that the power is turned on.
  2. Check the connections between the ice maker and the refrigerator. Make sure that the connections are secure.
  3. Check the ice maker motor itself. Make sure that the motor is not damaged or burned out.

If you have checked all of these things and the error code is still appearing, then the ice maker motor is probably faulty and needs to be replaced.

Here are the basic steps involved in replacing the ice maker motor:

  1. Unplug the refrigerator from the power outlet.
  2. Remove the ice maker from the refrigerator.
  3. Disconnect the old ice maker motor from the connections.
  4. Connect the new ice maker motor to the connections.
  5. Replace the ice maker in the refrigerator.
  6. Plug the refrigerator back into the power outlet.

Additional Troubleshooting Tips

Here are some additional troubleshooting tips that may help you resolve error code F12:

  • Make sure that the freezer temperature is set to the correct setting. The ideal temperature for ice making is 0 degrees Fahrenheit (-18 degrees Celsius).
  • Make sure that the ice maker bin is not full. If the ice maker bin is full, the ice maker will not be able to make more ice.
  • Clear any obstructions that may be blocking the ice maker.

If you have tried all of these troubleshooting tips and the error code is still appearing, then the ice maker motor is probably faulty and needs to be replaced.

Continue reading